Baron Grips & Risers_KICKBACK RISERS - BLACK - Manual

Page: 1 BA-7410U & BA-7410B
KICKBACK RISERS - FOR SELECT MODELS OF
YAMAHA-HONDA-KAWASAKI-SUZUKI &
HARLEY-DAVIDSON
CAUTION! We Strongly recommend that a qualified technician install this kit
if you do not completely understand the instructions prior to the install.Our
install guides provide a basic outline on the proper installation of our
products. Further tuning and/or fitment may be required. Baron bears no
responsibility on installation costs associated with this product.
Revision: 1.8 - 09/25/2012
Install Time: Usually under 1 hour
INCLUDED IN THE KIT:
(2) Baron Kickback Risers w/Top Clamps
(6) Mount Studs (2ea. Blue 12MM, Red 12MM &Black
10MM)
(4) Large Washers (2 for each set of studs; Blue/Red
use the same size nut) (10MM & 12MM)
(4) Nylock Nuts (2 for each set of studs; Blue/Red use
the same size nut) 10MM x1.25 & 12MM x1.25
TOOLS REQUIRED:
2.5mm - 8mm Allen Wrenches
12, 14 & 17mm Open-End Wrench
10 , 12, 14 & 17mm Sockets
Phillips & Flat Screwdrivers
Factory Service Manual
INSTRUCTIONS:
CAUTION: We suggest covering your fuel tank, front fender and headlight with towels or protective covering
to prevent damage.
1. Remove your stock bars & risers following your service manual.
NOTE: Depending on the bike model your working with it may be possible to remove the handlebar from the
risers and lay them forward on the fender, headlight or possibly back onto the tank (After placing towels or a
protective cover down). Some models may have hole plugs in the riser bolts which would need to pried out in
order to insert Allen wrench into the riser cap bolts. These covers may require a miniature screwdriver or
something with a thin edge to pry them loose.
SUGGESTION: Most stock bikes come equipped with a wire cable/line guide mounted under the triple tree and
usually attached the riser mount bolts. We recommend you permanently remove these cable/line guides as this
frees up additional cable and line length.
2. Select the appropriate size stud for your bike by matching the diameter and length to your stock riser bolts
from the provided sets. H-D models re-use the stock 1/2"-13 bolts. If you wish to replace the stock H-D bolts
you can you can purchase 1/2"-13 bolts in the appropriate length at most hardware stores and we suggest you
get a Grade 8 material.
3. Test fit the studs in the triple tree before continuing by threading the stud into the base of the riser and
installing the riser and stud into the triple tree mount holes to be sure the stud penetrates the triple tree with
enough exposed threads to allow the Nylock nut to thread fully onto the stud.
4. With fitment confirmed, remove the top clamps from each riser. Thread the selected studs into the risers
being sure to use RED Loctite® in the base of the riser on the 1/2" sections of the studs. Be sure the 1/2"x13
portion of the studs is threaded into the base of the riser until the last of the 1/2" threads are even with the base
of the risers. If necessary you may thread both nuts onto the stud as a "Jam-Nut" to help in threading if they
are difficult to turn by hand (do not use vise grips or pliers as they will damage the threads).
Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or
fitment may be required. Barons bears no responsibility on installation costs associated with this product.
© 2013 Barons Custom Accessories
5221 Oceanus Drive Huntington Beach, CA 92649 (925)583-2499 - Ph. (714)901-0520 - Fax www.baronscustom.com [email protected]