Document Outline

• Suretest Operation Manual.pdf
  • TABLE OF CONTENTS
  • Using this Manual
    • Conventions
      • Chapter References
      • Equipment Damage
        • IMPORTANT
      • Safety Messages
        • • DANGER
            • • WARNING
            • CAUTION
              • WARNING
      • Safety Information
  • Important Safety Instructions
    • Read All Instructions
      • • SAVE THESE INSTRUCTIONS
          • WARNING
          • WARNING
          • WARNING
          • WARNING
          • WARNING
  • CHAPTER 1
  • CHAPTER 2
  • Functional Descriptions and Specifications
    • SURETEST Base Unit
      • • • • • • FRONT PANEL
            • SURETEST DISPLAY
            • Front Panel Membrane Cursor and Function Keys
            • Power Up Sequence
    • Setup Mode
      • • • • E- INPUT AC VOLTAGE
    • SURETEST Transducers
    • Transducer Dimensions/Transducer Torque Range
    • Display Resolution for Transducers
    • Specifications
    • SURETEST Torque Calibration System
    • System Accuracy
    • Temperature Drift
    • Display Accuracy
    • Temperature
      • Operating Temperature
    • Storage
      • Temperature Drift
    • Dimensions
    • Weight
    • Data Storage/Recall w/Date Time Stamp
    • Statistical Analysis
    • Printer Serial Output Port
      • • Serial Communications
    • Analog Output
    • Loader Control Relays
    • Display Capacity
    • Units of Measurement
    • Accuracy
    • Range and Resolution
    • Temperature
      • • Output Torque
          • • CHAPTER 3
            • SETUP AND PROGRAMMING
      • SURETEST TORQUE CALIBRATION SYSTEM SETUP
        • • Back panel connections
      • Setting Up the SURETEST Torque Calibration System
      • Powering the Equipment
    • Programming Setup
  • Setting up Date and Time
    • • Setting Up High and Low Limits Alert
      • Set-up AUTO CLEAR
      • DATA LIST Memory
        • Clear Single Memory Location
        • Clear All Memory Locations
        • Setting Up Printer/PC Ports
          • • • • • CHAPTER 4
  • SURETEST TORQUE CALIBRATION SYSTEM SETUP
    • • • • • Testing Torque Wrenches and Drivers
            • Selecting a Transducer
            • Installing a Transducer
            • Dial and Bending Beam Torque Wrenches and Screwdrivers
    • WARNING
      • • • • • Adjustable or Preset “Click” Wrenches and Screwdrivers
    • WARNING
      • • • • Testing Power Tools
            • Non-Impact Tools
      • WARNING
        • • Displaying Statistical Analysis
        • Displaying Statistical Analysis
          • • Printing Statistical Analysis
            • Displaying or Downloading Data List
              • Downloading Data List to Printer
                • • Mounting Details
          • Torque Under 250 ft lb
          • Torque Over 250 ft lb
            • Figure 5-2: Single High Torque Transducer Mounting Detail
  • WARNING
    • • • • Quick Check
  • WARNING
    • • • Suggested Transducer Calibration Check Points, Bars, Hangers and Weights
        • Suggested Transducer Calibration Check Points, Bars, Hangers and Weights
  • Torque Calibrations
    • • • • SURETEST New Transducer Calibration
  • Procedure
  • SURETEST Indicator Calibration
  • Procedure
    • No Transducer Connected
      • • • • • • Calibrate tester
              • G
              • Gravitational Effects
          • Gravitational Charts
          • Acceleration Due to Gravity for Sea Level at Various Latitudes
          • Free Air Correction for Altitude
      • Correction Factor for Check Point Readings
      • Correction Factor for Weights
        • • CHAPTER 6
    • Application
    • Power
  • WARNING
    • Transducer Rotation
    • SURETEST Torque Calibration System
    • Functional Description
    • Torque Tester/Calibrator
      • A- Transducer Mounting
      • B- Hand Crank
      • C- Reaction Block
      • D- Linear Bearings
      • E- Reaction Pins
  • IMPORTANT
    • • F- Drive Adaptor
        • Loader Rear Panel Controls
      • A- Fuse
      • B- Voltage Select
      • C- AC Power Input
      • D- Solenoid Control
        • Ball Handle Adaptor
      • A- Quick Release Pins
      • C & D- Bracket Knobs
      • E- 4-in-1 Adapter Bracket
        • Types of Loader Testing
    • Torque Driver Testing
    • Torque Multiplier Testing
  • Appendix A
    • Accessories
      • Component Description Drawer-Cutout
        • Optional Transducers and Accessories
          • Component Description Drawer-Cutout
            • • • • Component Description Drawer-Cutout
            • Calibration Accessories
              • Component Description Drawer-Cutout
                • Component Description Drawer-Cutout