Yamaha Junior Kit - Manual (Page 2)

● JK6F42CMK ● JK6F41AMK
Bass Drum
Floor Tom Tom Tom
Drum Stool
Foot Pedal Hi-Hat Stand
Clamp
Cymbal Stand X2 Snare Stand
■ Drum Stool Assembly
1. Extend the Legs, slide the Leg Base to the end of the Base Section.
2. Insert the Upper Tube Section into the Leg Base’s Joint Section
(Make sure the tooth on the position clamp is facing down).
3. After adjusting the height of the Upper Tube Section, firmly tighten the Wing
Bolt on the Base Section.
4. Loosen the Wing Nut on the Position Clamp on the Upper Tube Section,
align the Position Clamp with the Joint and tighten the Wing Nut. With the
Position Clamp set in place, the stool will be set to the same height every
succeeding time the stool is assembled.
5. Attach the Seat to the Upper Tube Section and tighten the Wing Bolt.
6. Repeat steps 3 and 4 to adjust the stool height.
Thank you for purchasing the Yamaha “JUNIOR KIT” drum set.
Before you use, please thoroughly read this Assembly Manual and use the drum set in a safe and proper manner.
■ Drum Set Components
■ Setting Up
Hi-Hat Stand
Foot Pedal
When making adjustments to your settings always make sure to loosen the fixing bolt.
Parts will suffer damage if the part is adjusted with force when the fixing bolt is tightened.
Floor Tom
Bass Drum
Cymbal Stand
Tom Tom
Snare Drum
Clamp Cymbal Stand
■ Bass Drum Assembly
1. Place the head then the hoop onto the shell. Use the bass drum bolts, washers and the bass
drum hooks to secure the head and the hoop to the shell by tightening each bolt gradually in a
diagonal fashion.
2. Loosen the bass drum leg bolts and rotate the bass drum legs, (Fig. A) then loosely secure the
leg in place. Once you have determined the position of the leg, tighten the bass drum bolts to
secure the leg in place. (An alignment gauge is supplied on the bass drum leg base and bass
drum leg to aid in setting leg angles.)
To adjust the leg length, loosen the bass drum length key bolt (Fig. B) with a tuning key, adjust
the length of the leg, and firmly tighten the length key bolt.
Rotate the leg rubber either direction to secure the rubber to the bass drum leg. (Fig. C)
3. Insert the clamp into the pipe clamp and firmly tighten the tom-holder bolt.
Shell
Head
Hoop
Tuning Key
Pipe Clamp
Clamp
(B)
(A)
Washers
Bass Drum Leg Bolt
Bass Drum Length
Key Bolt
Bass Drum Bolts
Clamp Bolt
Tuning Key
(C) Rotate the rubber tip either direction
to fix in position.
Rubber Tip
BD Riser
Memory
Clamp
● Attaching the BD Riser
(Plate for FP Attachment)
Insert the BD riser into the pipe
clamp and tighten the bolt.
❈ After the position has been deter-
mined, set the memory clamp.
Pipe
Clamp
Seat
Wing Bolt
Drum Key Bolt
Upper Tube
Section
Hexagonal Nut
Position Clamp
Line
Joint
Leg
Leg Base
Wing Bolt
Base Section
Snare Drum
● If the stool is used in a high position, make sure that the Upper Tube Section is in-
serted at least 6cm into the Leg Base’s Joint Section. The line on the upper pipe indi-
cates the minimum required depth.
● Do not loosen the bolt that fixes the Leg in place marked with a “ ”. The stool may
become unstable causing an accident resulting in injury.
● Front View
● Back View
❈ Cymbals are
optional
Bass Drum Leg
6cm
Drum Stool
Snare Stand