Peerless Lighting IADW8 - T5_T5HO - Manual

LAMPING OPTIONS
SPECIFICATIONS
CATALOG NUMBER
S P E C I F I C A T I O N S
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: [email protected] • PeerlessLighting.com
Type: ________________________
Project: ______________________
1
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “IceTray” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx Direct T5/T5HO
IADW8 IceTray Angular Wall
Examples: IADW8 1 54T5HO OPI 40FT R12 277 GEB10 SCT LP835 C100 — IADW8 1 54T5HO OPI 32FT R8 277 GEB10 1SE EL SCT LP835 C041
Wall Mount IADW8
IceTray Angular Wall
Direct
Direct T5/T5HO
IADW8 - 1
Wall Mount
3 13 ⁄
16
” 3 ⁄
8
”
7”
Construction
Nominal 4” x 7” with extruded aluminum spine
and nominal four 4’ one-piece aluminum baffle
assemblies. Steel and die-cast aluminum sculptured
end cap.
Reflectors
White painted center reflector (nominal 90%
reflectance).
Shielding
Straight blade baffles with intermediate brightness
opal acrylic diffuser overlay.
Finish
Satin anodized or white polyester powder paint.
Satin anodized finish consists of satin anodized
housing, clear-coated aluminum baffles and end
caps painted C110 to match. Note that clear coated
aluminum baffles retain the slight imperfections
and characteristics of the raw aluminum source
material. Custom colors available, consult factory.
Electrical
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
Luminaire Length
4’, 8’, and 12’ lengths in a single section for exact
suspension spacing of 4’, 8’ and 12’. For total
luminaire length, add 1 3 ⁄
8
” for each end cap. Using
internal joiners 4’, 8’, and 12’ sections can be joined
to form longer rows. Individual 2’ and 3’ units also
available, consult factory
__________ __________ __________ __________ _________ __________ __________ __________ __________
Luminaire
IADW8
# of
Lamps in
Cross
Section
1
Lamp Type
28T5 28W T5
54T5HO 54W T5HO
Shielding
OPI Intermediate brightness
opal diffuser
OPD Standard brightness opal
diffuser
Luminaire
Row
Length
X FT
(4’ increments)
Maximum
Section
Length
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
Voltage
120
277
347
Ballast Type
GEB10 <10% THD Electronic
ADEZ 1,2 Advance Mark 10 dim
DMHL3D 1 Lutron Hi-Lume dim
OSDIM 1,2 Osram 0-10V dim
Reference Ballast Wizard on website
or consult factory for other options.
# of Emergency
Modules
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
______________ ________________ ________________ ______________ _________________________________
Emergency Type 3
(Blank) None
EC Emergency circuit
EL 1 Emergency battery
pack
EN 1 Emergency battery
pack
w/night light circuit
Switching
SCT Single circuit
Lamp Color
L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI
Available with T5 only:
LP830P 3000K 80+
CRI Premier
LP835P 3500K 80+
CRI Premier
LP841P 4100K 80+
CRI Premier
Reference Lamp Chart on
website or consult factory
for other options.
Finish
C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish
Options
DL Damp location label
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
GLR Fusing (fast blow)
GMF Fusing (slow blow)
NYC New York City code
Notes:
1 Not available in 347V
2 Not available with 28T5 lamps
3 Emergency type is installed in last 4’ of luminaire sections.
Separate feed required unless ELS or ELS2 is specified