Peerless Lighting EGCW4 - T5_T5HO - Manual

LAMPING OPTIONS
SPECIFICATIONS
CATALOG NUMBER
S P E C I F I C A T I O N S
__________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ __________ _____________________
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: [email protected] • PeerlessLighting.com
Type: ________________________
Project: ______________________
1
© 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Lightedge” are registered trademarks of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx Indirect-Direct T5/T5HO
EGCW4 Lightedge Curved Wall I/D
Examples: EGCW4 1 54T5HO 36FT R12 120 GEB10 2SE EL SCT LP835 C100 — EGCW4 2 54T5HO 12FT R12 277 GEB10 DCT L/LP C100
Wall Mount EGCW4
Lightedge Curved
Wall I/D
Indirect-Direct T5/T5HO
EGCW4 - 1
7 1 ⁄
2
”
EGCW4 - 2
7 1 ⁄
2
”
Construction
Housing and end caps are extruded aluminum
forming a 7 1 ⁄
2
” x 2 1 ⁄
4
” curvilinear profile.
Reflectors
Die-formed reflectors combine hammertone
specular aluminum and baked white enamel
(nominal reflectance 90%). Prismatic acrylic kicker
lens on 1 lamp product.
Shielding
Parabolic semi-specular aluminum baffles with
opal diffuser.
Finish
Satin anodized standard. Custom colors available,
consult factory.
Electrical
Specify 120V, 277V or 347V. Pre-wired with 16AWG
fixture wires. For special circuiting or wire gauge,
consult factory. Plug-in electrical connectors
included. UL and C-UL listed.
Luminaire Length
4’, 8’ and 12’ lengths in a single section. For total
luminaire length add 4” for each end cap. Using
internal joiners, 4’, 8’ and 12’ sections can be joined
to form longer-length luminaires.
__________ __________ __________ _________ __________ __________ __________ __________
Luminaire
EGCW4
# of Lamps in
Cross Section
1
2
Lamp Type
28T5 28W T5
54T5HO 54W T5HO
Luminaire Row
Length
X FT
(4’ increments)
Maximum
Section Length
R4 4’ section(s)
R8 8’ section(s)
R12 12’ section(s)
Voltage
120
277
347
Ballast Type
GEB10 <10% THD Electronic
ADEZ 1,2 Advance Mark 10 dim
DMHL3D 1 Lutron Hi-Lume dim
OSDIM 1,2 Osram 0-10V dim
Reference Ballast Wizard on website
or consult factory for other options.
# of Emergency Modules
(Blank) None
1SE 1 section
2SE 2 sections
XSE X sections
______________ ________________ ________________ ______________ _________________________________
Emergency Type 3
(Blank) None
EC Emergency circuit
EL 1 Emergency battery pack
EN 1 Emergency battery pack
w/night light circuit
Switching
SCT Single circuit
DCT Dual circuit
Lamp Color
L/LP No lamp
LP830 3000k 80+ CRI
LP835 3500k 80+ CRI
LP841 4100k 80+ CRI
Available with T5 only:
LP830P 3000K 80+ CRI Premier
LP835P 3500K 80+ CRI Premier
LP841P 4100K 80+ CRI Premier
Reference
Lamp Chart on website or
consult factory for other options.
Finish
C041 White white (low gloss)
C100 Satin anodized finish
C099 Custom finish
Options
DL Damp location label
DU Dust cover
ELH Emergency through wiring w/separate feed
ELS Emergency through wiring w/single feed, shared neutral
ELS2 Emergency through wiring w/single feed, separate neutrals
EXT 3” extended mount (consult factory)
GLR Fusing (fast blow)
GMF Fusing (slow blow)
Notes:
1 Not available in 347V
2 Not available with 28T5 lamps
3 Emergency type is installed in last 4’ of luminaire sections.
Separate feed required unless ELS or ELS2 is specified
2 1 ⁄
4
” 2 1 ⁄
4
”