Rainbow Electronics MAXQ3108 - Manual (Page 44)

MAXQ3108
Low-Power, Dual-Core Microcontroller
44 ______________________________________________________________________________________
Special Function Register Bit Descriptions (continued)
I2CIE (02h, 04h) I 2 C Interrupt Enable Register (16-Bit Register)
Initialization: This register is cleared to 0000h on all forms of reset.
Read/Write Access: Unrestricted read/write access.
I2CIE.0: I2CSRIE
I 2 C START Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when a START
condition is detected (I2CSRI = 1). Clearing this bit to 0 disables the START detection interrupt
from generating.
I2CIE.1: I2CTXIE
I 2 C Transmit Complete Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when
the transmit interrupt flag is set (I2CTXI = 1). Clearing this bit to 0 disables the transmit interrupt
from generating.
I2CIE.2: I2CRXIE
I 2 C Receive Ready Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when the
receive interrupt flag is set (I2CRXI = 1). Clearing this bit to 0 disables the receive interrupt from
generating.
I2CIE.3: I2CSTRIE
I 2 C Clock Stretch Interrupt Enable. Setting this bit to 1 generates an interrupt to the CPU when the
clock stretch interrupt flag is set (I2CSTRI = 1). Clearing this bit disables the clock stretch interrupt
from generating.
I2CIE.4: I2CTOIE
I 2 C Timeout Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when a timeout
condition is detected (I2CTOI = 1). Clearing this bit to 0 disables the timeout interrupt from
generating.
I2CIE.5: I2CAMIE
I 2 C Slave Address Match Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU
when the I 2 C controller detects an address that matches the I2CSLA value (I2CAMI = 1). Clearing
this bit to 0 disables the address match interrupt from generating.
I2CIE.6: I2CALIE
I 2 C Arbitration Loss Enable. Setting this bit to 1 causes an interrupt to the CPU when the I 2 C
master loses in an arbitration (I2CALI = 1). Clearing this bit to 0 disables the arbitration loss
interrupt from generating.
I2CIE.7: I2CNACKIE
I 2 C NACK Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when a NACK is
detected (I2CNACKI = 1). Clearing this bit to 0 disables the NACK detection interrupt from
generating.
I2CIE.8: I2CGCIE
I 2 C General Call Interrupt Enable. Setting this bit to 1 generates an I2CGCI (general call interrupt)
to the CPU when general call is enabled (I2CGCEN = 1). Clearing this bit to 0 disables the general
call interrupt from generating.
I2CIE.9: I2CROIE
I 2 C Receiver Overrun Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when a
receiver overrun condition is detected (I2ROI = 1). Clearing this bit to 0 disables the receiver
overrun detection interrupt from generating.
I2CIE.10: Reserved Reserved. Reads return 0.
I2CIE.11: I2CSPIE
I 2 C STOP Interrupt Enable. Setting this bit to 1 causes an interrupt to the CPU when a STOP
condition is detected (I2CSPI = 1). Clearing this bit to 0 disables the STOP detection interrupt from
generating.
I2CIE.[15:12]: Reserved Reserved. Reads return 0.
TB0R (04h, 04h) Timer B 0 Capture/Reload Value
Initialization: This register is cleared to 0000h on all forms of reset.
Read/Write Access: Unrestricted read/write.
TB0R.[15:0]:
Timer B Capture/Reload Bits 15:0. This register is used to capture the TBV value when timer B is
configured in capture mode. This register is also used as the 16-bit reload value when timer B is
configured in autoreload mode.