Absolute maximum ratings, Electrical characteristics – Rainbow Electronics MAX8902B User Manual
Page 2
MAX8902A/MAX8902B
Low-Noise 500mA LDO Regulators
in a 2mm x 2mm TDFN Package
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
BYP, EN, IN, OUT, SELA, SELB, POK to GND, GS to GND, FB,
OUTS to GND .....................................................-0.3V to +6.0V
Output Short-Circuit Duration.....................................Continuous
Continuous Power Dissipation (T
A
= +70°C)
8-Pin, 2mm x 2mm TDFN
(derate 11.9mW/°C above +70°C) .............................953.5mW
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature Range ............................-40°C to +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
ELECTRICAL CHARACTERISTICS
(V
IN
= V
EN
= 5V, OUTS = OUT, circuit of Figure 2 (MAX8902A) and Figure 3 (MAX8902B), T
A
= -40°C to +125°C, unless otherwise
noted.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
IN
Input Voltage Range
1.7
5.5
V
Input Undervoltage Lockout
V
IN
rising, 100mV typical hysteresis
1.5
1.6
1.7
V
OUT
Output Voltage Range
V
IN
≥ V
OUT
+ 0.1V
0.6
5.3
V
Output Voltage Accuracy
V
IN
= 1.7V to 5.5V for V
OUT
≤ 1.4V,
V
IN
= (V
OUT
+ 0.3V) to 5.5V for V
OUT
> 1.4V,
I
OUT
= 0.1mA to 500mA
-1.5
+1.5
%
Load Regulation
I
OUT
= 0.1mA to 500mA
0.02
%
Line Regulation
V
IN
= 1.7V to 5.5V for V
OUT
≤ 1.4V,
V
IN
= (V
OUT
+ 0.3V) to 5.5V for V
OUT
> 1.4V,
I
OUT
= 200mA
0.04
%
V
IN
≥ 3.6V, T
A
≤ +85°C
50
100
V
IN
≥ 3.6V, T
A
≤ +125°C
120
Dropout Voltage
(Note 2)
I
OUT
= 500mA
V
IN
= 1.7V
150
mV
Current Limit
V
OUT
= 95% of regulation, V
IN
= V
OUT
+ 0.5V
600
700
800
mA
Output Noise
I
OUT
= 100mA, f = 10Hz to 100kHz, C
BYP
= 0.01µF
16
µV
RMS
f = 5kHz
92
f = 10kHz
85
Power-Supply Rejection Ratio
I
OUT
= 10mA
f = 100kHz
62
dB
OUTS (MAX8902A only)
OUTS Input Bias Current
In regulation
0.5
7.0
µA
FB (MAX8902B only)
FB Threshold Accuracy
V
IN
= 1.7V to 5.5V, I
OUT
= 0.1mA to 500mA
0.591
0.600
0.609
V
T
A
= +25°C
-0.1
0.02
+0.1
FB Input Bias Current
V
FB
= 0.6V
T
A
= -40°C
0.03
µA
BYP
BYP Capacitor Range
Regulator remains stable
1
100
nF
BYP Startup Current
From BYP to GND during startup
50
µA