Rainbow Electronics MAX5839 - Manual

For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
General Description
The MAX5839 contains eight 13-bit, voltage-output digi-
tal-to-analog converters (DACs). On-chip precision out-
put amplifiers provide the voltage outputs. The device
operates from +14V/-9V supplies. Its bipolar output
voltage swing ranges from +9V to -4V and is achieved
with no external components. The MAX5839 has three
pairs of differential reference inputs; two of these pairs
are connected to two DACs each, and a third pair is
connected to four DACs. The references are indepen-
dently controlled, providing different full-scale output
voltages to the respective DACs. The MAX5839 oper-
ates within the following voltage ranges: V
DD = +7V to
+14V, V SS = -5V to -9V, and V CC = +4.75V to +5.25V.
The MAX5839 features double-buffered interface logic
with a 13-bit parallel data bus. Each DAC has an input
latch and a DAC latch. Data in the DAC latch sets the
output voltage. The eight input latches are addressed
with three address lines. Data is loaded to the input
latch with a single write instruction. An asynchronous
load input (LD) transfers data from the input latch to the
DAC latch. The LD input controls all DACs; therefore, all
DACs can be updated simultaneously by asserting the
LD pin.
An asynchronous CLR input sets the output of all eight
DACs to the respective DUTGND input of the op amp.
Note that CLR is a CMOS input, which is powered by
V
DD . All other logic inputs are TTL/CMOS compatible.
The “A” grade of the MAX5839 has a maximum INL of
±2LSBs, while the “B” grade has a maximum INL of
±4LSBs. Both grades are available in 44-pin MQFP
packages.
Applications
Industrial Process Controls
Arbitrary Function Generators
Avionics Equipment
Minimum Component Count Analog Systems
Digital Offset/Gain Adjustment
SONET Applications
Automatic Test Equipment (ATE)
Features
♦ Full 13-Bit Performance Without Adjustments
♦ 8 DACs in a Single Package
♦ Buffered Voltage Outputs
♦ Unipolar or Bipolar Voltage Swing to +9V and -4V
♦ 22µs Output Settling Time
♦ Drives up to 10,000pF Capacitive Load
♦ Low Output Glitch: 30mV
♦ Low Power Consumption: 10mA (typ)
♦ Small Package: 44-Pin MQFP
♦ Double-Buffered Digital Inputs
♦ Asynchronous Load Updates All DACs
Simultaneously
♦ Asynchronous CLR Forces All DACs to DUTGND
Potential
MAX5839
Octal, 13-Bit Voltage-Output DAC
with Parallel Interface
________________________________________________________________ Maxim Integrated Products 1
DUTGNDGH
OUTH
REFGH-
REFGH+
V SS
CLR
D12
D11
D10
D9
D8
DUTGNDAB
OUTA
REFAB-
REFAB+
V DD
V SS
LD
A2
A1
A0
CS
1
2
3
4
5
6
7
8
9
10
11
12 13 14 15 16 17 18 19 20 21 22
44 43 42 41 40 39 38 37 36 35 34
33
32
31
30
29
28
27
26
25
24
23
WR V
CC
GND
D0 D1 D2 D3 D4 D5 D6 D7
OUTB OUTC DUTGNDCD OUTD REFCDEF- REFCDEF+ V
DD
OUTE DUTGNDEF OUTF OUTG
MQFP
MAX5839
TOP VIEW
19-1603; Rev 0; 1/00
Functional Diagram appears at end of data sheet.
Pin Configuration
Ordering Information
INL
(LSB)
±2
±4
±4
PIN-
PACKAGE
44 MQFP
44 MQFP
44 MQFP
TEMP. RANGE
0°C to +70°C
0°C to +70°C
-40°C to +85°C
PART
MAX5839ACMH
MAX5839BCMH
MAX5839BEMH
±2 44 MQFP -40°C to +85°C MAX5839AEMH