Timing characteristics – Rainbow Electronics MAX1403 User Manual
Page 7
0
100
MAX1403
+3V, 18-Bit, Low-Power, Multichannel,
Oversampling (Sigma-Delta) ADC
_______________________________________________________________________________________
7
TIMING CHARACTERISTICS
(V+ = +2.7V to +3.6V, V
DD
= +2.7V to +3.6V, AGND = DGND, f
CLKIN
= 2.4576MHz, input logic 0 = 0V, logic 1 = V
DD
, T
A
= T
MIN
to
T
MAX
, unless otherwise noted.) (Notes 20, 21, 22)
Bus Relinquish Time After SCLK
Rising Edge (Note 27)
t
10
ns
SCLK Falling Edge to Data Valid
Delay (Notes 25, 26)
t
6
0
100
ns
INT High Time
t
INT
560 / N
·
t
CLKIN
ns
X2CLK = 1, N = 2
(2
·
MF1 + MF0)
Crystal oscillator or clock exter-
nally supplied for specified perfor-
mance (Notes 23, 24)
SCLK Setup to Falling Edge CS
t
4
30
ns
SCLK Low Pulse Width
t
8
100
ns
10
100
SCLK Rising Edge to INT High
(Note 28)
t
11
200
CS Rising Edge to SCLK Rising
Edge Hold Time (Note 22)
t
9
0
ns
SCLK High Pulse Width
t
7
100
ns
CS Falling Edge to SCLK Falling
Edge Setup Time
t
5
30
ns
280 / N
·
t
CLKIN
INT to CS Setup Time (Note 9)
t
3
X2CLK = 0, N = 2
(2
·
MF1 + MF0)
0
ns
RESET Pulse Width Low
t
2
100
ns
Master Clock Input Low Time
f
CLKIN LO
0.4
·
t
CLKIN
ns
t
CLKIN
= 1 / f
CLKIN
, X2CLK = 0
Master Clock Input High Time
f
CLKIN HI
0.4
·
t
CLKIN
ns
t
CLKIN
= 1 / f
CLKIN
, X2CLK = 0
Master Clock Frequency
f
CLKIN
0.8
5.0
MHz
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
0.4
2.5
CONDITIONS
ns
X2CLK = 0
X2CLK = 1
Note 16:
The burn-out currents require a 500mV overhead between the analog input voltage and both V+ and AGND to operate
correctly.
Note 17:
Measured at DC in the selected passband. PSR at 50Hz will exceed 120dB with filter notches of 25Hz or 50Hz and FAST
bit = 0. PSR at 60Hz will exceed 120dB with filter notches of 20Hz or 60Hz and FAST bit = 0.
Note 18:
PSR depends on gain. For a gain of +1V/V, PSR is 70dB typical. For a gain of +2V/V, PSR is 75dB typical. For a gain of
+4V/V, PSR is 80dB typical. For gains of +8V/V to +128V/V, PSR is 85dB typical.
Note 19:
Standby power-dissipation and current specifications are valid only with CLKIN driven by an external clock and with the
external clock stopped. If the clock continues to run in standby mode, the power dissipation will be considerably higher.
When used with a resonator or crystal between CLKIN and CLKOUT, the actual power dissipation and I
DD
in standby
mode will depend on the resonator or crystal type.
30
ns
t
12
SCLK Setup to Falling Edge CS
SERIAL-INTERFACE READ OPERATION
SERIAL-INTERFACE WRITE OPERATION