Rainbow Electronics MAX530 - Manual (Page 7)

MAX530
+5V, Low-Power, Parallel-Input,
Voltage-Output, 12-Bit DAC
_______________________________________________________________________________________ 7
______________________________________________________________Pin Description
* This applies to 4 + 4 + 4 input loading mode. See Table 2 for 8 + 4 input loading mode.
D0 (LSB) Input Dta when A0 = 0 and A1 = 1, or D8 Input when A0 = A1= 1* D0/D8 24
Positive Power Supply (+5V) V DD 23
Offset Resistor Pin. Connect to VOUT for G = 1, to AGND for G = 2, or to REFIN for bipolar output. ROFS 22
Feedback Pin. Op-amp feedback resistor. Always connect to VOUT. RFB 21
Voltage Output. Op-amp buffered DAC output. VOUT 20
Negative Power Supply. Usually ground for single-supply or -5V for dual-supply operation. V SS 19
Reference Output. Output of the internal 2.048V reference. Tie to REFIN to drive the R-2R DAC. REFOUT 18
Reference Ground must be connected to AGND when using the internal reference. Connect to V DD
to disable the internal reference and save power.
REFGND 17
Load DAC Input (active low). Driving this asynchronous input low transfers the contents of the input
latch to the DAC latch and updates VOUT.
LDAC 16
Clear (active low). A low on CLR resets the DAC latches to all 0s. CLR 15
Analog Ground AGND 14
Reference Input. Input for the R-2R DAC. Connect an external reference to this pin or a jumper to
REFOUT (pin 18) to use the internal 2.048V reference.
REFIN 13
Digital Ground DGND 12
Chip Select (active low). Enables addressing and writing to this chip from common bus lines. CS 11
Write Input (active low). Used with CS to load data into the input latch selected by A0 and A1. WR 10
Address Line A1. Set A0 = A1 = 0 for NBL and NBM, A0 = 0 and A1 = 1 for NBL, A0 = 1 and
A1 = 0 for NBM, or A0 = A1 = 1 for NBH. See Table 2 for complete input latch addressing.
A1 9
Address Line A0. With A1, used to multiplex 4 of 12 data lines to load low (NBL), middle (NBM),
and high (NBH) 4-bit nibbles. (12 bits can also be loaded as 8+4.)
A0 8
D7 Input Dta, or tie to D3 and multiplex when A0 = 1 and A1 = 0* D7 7
D6 Input Dta, or tie to D2 and multiplex when A0 = 1 and A1 = 0* D6 6
D5 Input Dta, or tie to D1 and multiplex when A0 = 1 and A1 = 0* D5 5
D4
D3/ D11
D2/ D10
D1/ D9
NAME
D4 Input Dta, or tie to D0 and multiplex when A0 = 1 and A1 = 0* 4
D3 Input Dta, when A0 = 0 and A1 = 1, or D11 (MSB) Input when A0 = A1 =1* 3
D2 Input Dta, when A0 = 0 and A1 = 1, or D10 Input when A0 = A1 = 1* 2
D1 Input Dta, when A0 = 0 and A1 = 1, or D9 Input when A0 = A1 = 1* 1
FUNCTION PIN