Prokit's Industries 3PK-NT015N - Manual

OPERATION: Test Result(RJ45)
(A).Test for RJ45(or RJ11) cable 1. Continuity: 1 2 3 4 5 6 7 8 G Pin 1 to G are continued
1. Slide the master unit power switch on. ( LED on)
2. Connect cable's one end to the master's connector,and other end
to the remote.
2. Open: 1 2 3 4 5 6 7 8 G Pin 2 and 6 are opened
3.Then press the" TEST" button , as soon as the LED indicator ( LED off)
will display the tested result.
(1) The cable is connected properly, the LEDs light for each pin
3. Short: 1 2 3 4 5 6 7 8 G Pin 2 and 4 are shorted
and buzz once "BI --" , then stop. ( LED on)
Function LED : Battery, Isolation,Connected,will be light.
(2) If open, the LEDs will not be light and buzz warning "BI- - -" 4. Miswire: 1 2 3 4 5 6 7 8 G Pin 4 and 6 are miswired
Function LED : Battery, Isolation,Connected, will be light. ( LED on)
(3) If short, the LEDs will be light and buzz TEST
warning "BI-BI-" CONNECTED SHORT
Function LED : Battery,Short, will be light. 50K ISOLATION MISWIRING
(4) If miswiring, the LEDs will be light and buzz warning"BI-BI-" BATTERY NO CONNECTION
Function LED : Battery,Connected,Miswiring, will be light. OFF ON
(5) The cable's "Isolation" under 50K Ohm the isolation LED
will be light & flashing
POWER
(6) The cable's "Resistance" up to 35 Ohm the LED indicator Note:
will be display open. Please don't operate the tester in live circuit because it may damaged
the tester.
Part No. 3PK-NT015N
Before using, please first make the self-test by the attached cable and adapter.
OPERATION: Test Result(BNC) INTRODUCTION:
(B).Test for BNC Cable 1. Continuity: 1 2 3 4 5 6 7 8 G Pin 1 and pin 2 are continued The Portable Lan Cable Tester is consists of shield RJ-45 and is
1. Slide the master unit power switch on. ( LED on) equipped with BNC . The tester also offers easy operation,
2. Connect cable's one end to the master's connector,and other end the user begins testing by simply pushing a button. The multiple
to the remote.The remote unit inside installed a 75 Ohm risistor. 2. Open: 1 2 3 4 5 6 7 8 G Pin 1 or Pin 2 is opened LEDs give a clear indication. This Lan Cable Tester is a newly
3.Then press the" TEST" button , as soon as the LED indicator ( LED off) designed and very practical tester that can be easily read the
will display the tested result. correct pin configuration of cable continuity, open, short, miswiring,
(1) The cable is connected properly, the LEDs light for pin 1 & pin 2 3. Short: 1 2 3 4 5 6 7 8 G Pin 1 and 2 are shorted no connection & isolation.
and buzz once "BI --" , then stop. ( LED on)
Function LED : Battery,Connected, will be light. FEATURES:
(2) If open, the LEDs will not be light and buzz warning "BI-BI-" 4. Miswire: 1 2 3 4 5 6 7 8 G Pin 1 and 2 are miswired * Open/short wiring test
Function LED : Battery,Isolation, No connected will be light. ( LED on) * Connected wires display
(3) If short, the LEDs will be light and buzz warning "BI-BI-" TEST * No wire or termination indication
Function LED : Battery,Short, will be light. CONNECTED SHORT * Wrong connection / Non-parallel connection
(4) The cable's "Isolation" under 50K Ohm the isolation LED 50K ISOLATION MISWIRING * Ethernet 10 Base2 termination value detection
will be light & fiashing. But the remote unit no connected. BATTERY NO CONNECTION * Battery low indication
(5) Testing Ethernet 10BASE2 terminnator value range from OFF ON * Buzzer inside.
45 Ohm to 85 Ohm * BNC for testing 10 BASE2 Terminator value.
3. Battery LED light shows the battery is good, if flashing show POWER * Isolation Resistances 50 K ohms test
the battery is low. Note:
Please don't operate the tester in live circuit because it may damaged
the tester.
Lan Cable Tester