Prokit's Industries PT-1201 - Manual (Page 3)

PT-1201 User’s Manual
www.prokits.com.tw 4
eyes, additionally seek medical help. Liquid ejected form the battery
may cause irritation or burns.
6) Service
Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
Special Safety Advice for Cordless Drill
Only plug the Battery Charger in 230V for PT-1201F type and 120V for
PT-12011A type mains. Recharge the Battery only with the provided charger.
Before starting any work on walls, floors or similar, make sure that all power lines
in the work area are switched off at the main switchboard. Inspect the proposed
drill holes location for any utility lines (e.g. water, gas, power) before drilling. Use
a suitable device such as a metal or electricity line detecting device. If in doubt
contact a qualified electrician or your utility provider. Both tools and work-pieces
can heat up considerably during the drilling operation. Allow a sufficient period of
cooling before handling. Wear appropriate gloves.
Safety Advice for Rechargeable Battery and Charger
Use only the battery provided with the drill or a replacement rechargeable
battery from Pro’sKit and the provided charger. Only plug the battery charger in
230V for PT-1201F type and 120V for PT-1201A type mains. Protect battery and
battery charger from humidity. Do not operate the battery charger outdoors.
When it is not in use and before cleaning and servicing, disconnect the battery
charger from the power supply. Take special care of the battery. Avoid dropping it
onto any hard surface and do not subject it to pressure or any other form of
mechanical stress. Keep the battery away from extreme heat and cold. Do not
open or attempt to repair the battery or the battery charger. If any parts are
defective, have them repaired by a qualified technician or send them to our
service department for repair. Only charge the battery at an ambient
(surrounding air) temperature between 10ºC and 40ºC. A charged battery can
be used to power the machine under ambient temperature conditions between
0ºC and 50ºC.When not in use, store the battery in a dry place between 10ºC
and 30ºC.
Important! Danger! Never short-circuit the battery or expose it to moisture.
Do not store it together with any metal parts which could short-circuit the
contacts. The battery could overheat, start burning or explode.
If any person comes into contact with acid or similar internal fluids or
substances contained in the battery, wash off these substances
PT-1201 User’s Manual
www.prokits.com.tw 5
immediately with plenty of water. If these substances make contact with
the eyes, rinse with plenty of water and visit a doctor immediately.
Do not place the rechargeable battery into fire or water. It can explode. The
Rechargeable Battery should not be discarded to domestic refuse, regardless of
whether used or unused. You should return it to a local battery collection point in
accordance with Battery Regulations or return them to us suitably marked “Used
Battery”.
Technical Data
Model PT-1201A PT-1201F
Rated Voltage DC 12V DC 12V
No-load Speed
One Gear Speed:
0-550rpm
One Gear Speed: 0-550rpm
Range of Drill Bit
sizes
Φ 0.8 ~ 10mm Φ 0.8 ~ 10mm
Steel: Ø 6 mm Steel: Ø 6 mm
Concrete: Ø 8 mm Concrete: Ø 8 mm
Max. Drilling
Capacity
Wood: Ø10 mm Wood: Ø10 mm
Torque Setting 16 +1Position 16+1 Position
Output torque MAX 5 N.M MAX 5 N.M
Drive (Collet)
3/8" (10mm)
Keyless Chuck
3/8" (10mm) Keyless
Chuck
Battery Ni-Cd 12V 1000mAh Ni-Cd 12V 1000mAh
Charging Time 3-5 hours 3-5 hours
Free running
time 30-35 min. (unload
speed)
30-35 min. (unload speed)
Size 235*230*80mm 235*230*80mm
Weight
(include battery)
1.35kg 1.35kg
Adaptor
Model No: 5PK-1201-ADA
120V AC 60Hz
15V DC 400mA
Model No. : 5PK-1201-ADF
230V AC 50Hz
15V DC 400mA
Charger
Model No.5PT-1201-CH
Voltage: DC 15V 400mA
Protection Class II