StreetGlow Single Color LED Undercar Kit - Manual (Page 2)

Step 1 Unpack entire contents of packaging and check for any damaged products before moving to the testing sequence.
Step 2 Place all 4 LED tubes on a test bench and connect the 4 LED control wires of the tubes to the back of the
Digital LED Controller (DLC).
Step 3 Using a 12v DC power source, connect the DLC’s RED and YELLOW (Power) wires to the Positive (+) 12v
lead of the power supply. Note: DO NOT connect the BLUE (Alarm) wire for this test.
Step 4 Next connect the DLC’s BLACK (Ground) wire to the power supply’s Negative (-) output
Step 5 Press the Power ON/OFF button to activate all LED segments – ON. Note: If none of the LED’s light up, then
go back to Step 3 and check your connections for Power and Ground.
2 - 48” LED tubes
2 - 30” LED tubes
1 - Digital LED Controller (DLC)
14 - 3/4” tube mounting clamps
12 - 3/16” wire clamps
26 - 5/8” self-tapping screws
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING!
Quick Test Sequence
Step 1 Select a desired location for the Digital LED Controller (DLC) and mount using the supplied mounting hardware.
Step 2 With DLC mounted connect power and ground to the DLC’s power harness as shown in wiring connection diagram.
• YELLOW wire = 12v Battery (+)
• RED wire = 12v Ignition (+)
• BLACK Wire = Negative ground (-)
• BLUE wire = Alarm Negative input (-) (optional connection)
Note: Vehicles with after market alarms can use the ANLED100’s Alarm feature to activate when
Ignition Kill is enabled with a Negative trigger.
Step 3 Select the desired locations for the LED tube placement which are away from all fuel lines, exhaust systems,
areas of extreme heat, ABS components, SRS components, any moving parts and where lifts or jacks are
used to raise your vehicle. Note: LED tubes need to be mounted as to the recommended configuration
(see FIGURE 1 for details).
Step 4 Using the 3/4” tube mounting clamps and the 5/8” self-tapping screws, fasten the LED tubes to your
vehicle in the recommended mounting positions (4 mounting clamps per 48” tube, 3 clamps per 30” tube).
Step 5 Run the control wires from each LED tube underneath the vehicle up into the DLC location. It’s recommended
to run all wires in the shortest path to the DLC away from all fuel lines, exhaust systems, areas of extreme
heat, ABS components, SRS components, any moving parts, and where lifts or jacks are used to raise your vehicle.
Step 6 With all 4 control wires located at the DLC, plug each LED tube control wire into the back of the DLC
outputs (see FIGURE 1 for details).
Step 7 Once wiring and mounting for all components is completed, test the ANLED100’s 3 modes of operation
and the sequential lighting effects.
Installation Instructions
Step 1 Turn unit ON by pressing and holding ON/OFF button for 2 seconds
Step 2 Turn unit OFF by pressing and holding ON/OFF button for 2 seconds
Digital LED Controller (DLC) Operation
MODES: All LED’s On / Music Interface / Sequential Lighting Effects
Turn unit ON and select the desired MODE of operation by using the following steps:
Step 1 1st press MODE button = All LED’s On mode (solid show of lights)
2nd press MODE button = Music Interface mode (dances to the beat of your music)
3rd press MODE button = Sequential Lighting Effect mode (see FIGURE 2 for different effects)
• Alarm Mode = Activates when the BLUE wire is triggered with a Negative (ground) input
• This feature functions ONLY when the vehicle is off or when 12v is disconnected from the Ignition RED
wire (see FIGURE 1 for details)
• When the Alarm mode is active, the 3rd (middle) bank of LED’s will flash once per second under the vehicle
Step 2 Selecting different light shows
• When the DLC is in Sequential Lighting mode, you’re able to select up to 8 different lighting effects by pressing
the SEQ. button 3 times (see FIGURE 2 for details)
• To increase the speed of light, press and hold the SPEED button until desired effect is achieved
• To decrease the speed of light, press twice and hold the SPEED button until desired effect is achieved
Step 3 Enjoy!
Modes and Sequential Lighting Effects
Controller
BLACK (-)
YELLOW (+)
- +
BATTERY
OR
ALTERNATIVE POWER SOURCE
(IE: FUSEBOX)
Ground
Alarm
BLUE (-)
Ground
(Optional)
RED (+) IGNITION
CENTER OUT OUT CENTER
NIGHT CRUZIN'
1 2
RIGHT TO LEFT LEFT TO RIGHT
INCH WORM ALL FLASH
FIGURE
1
FIGURE
2
LED UNDERCAR KIT
I N S T A L L A T I O N I N S T R U C T I O N S
FRONT
REAR
WIRING DIAGRAM