Procom CX-Mount - Manual

CX-Mount
Circular Mini Mobile Mount
DESCRIPTION
Mobile mount gradually merging with the car roof.
Although mainly designed for roof mounting, installation can take place
anywhere on the car.
M6 thread whip-mounting system.
Designed for installation with access from the outside only.
Very low requirements to installation depth both under and after
installation.
With access available from the inside, installation is possible in a 14 mm
dia. hole.
Bendable section in mount makes whip tiltable 30° by hand.
Complete line of whips available for all communications bands up to
1300 MHz.
Mounting body made of stainless steel!
Choice between two connection principles:
CX-mount: FME-connection (supplied without cable).
CXP4-mount: Permanently attached 4 m cable terminated with FME-
connector.
ORDERING DESIGNATIONS
TYPE PRODUCT NO.
CX-Mount CX-mount with FME-system
CXP4-Mount CXP4-mount with 4 m cable and FME-connector
SPECIFICATIONS
MODEL CX-MOUNT
APPLICATION Mount for mobile antennas
FREQUENCY 0 - 1300 MHz
CONNECTION TO WHIP M6 thread stud
MATERIALS Stainless steel
Black chromed brass
Cu-nite brass
Weather- and shockproof plastics
COLOUR Black
HEIGHT Approx. 42 mm
INSTALLATION DIA. 32.5 mm
BUILD-IN DEPTH Active : 30 mm
Passive : 11 mm
RECOMMENDED
INSTALLATION TORQUE
4 ± 1 Nm
WEIGHT CX-version : Approx. 40 g
CXP4-version : Approx. 180 g
MOUNTING 18 mm dia. hole
ROOF THICKNESS Max. 2 mm
FME-SYSTEM ACCESSORIES
FME-CABLES
LENGTH TYPE NO.
1 m 1 m FME
2 m 2 m FME
3 m 3 m FME
4 m 4 m FME
5 m 5 m FME
6 m 6 m FME
4 m white 4 m FME-white
6 m white 6 m FME-white
12 m white 12 m FME-white
18 m white 18 m FME-white
FME-CONNECTORS
CONNECTOR ORDER NO.
FME-FME FME-FME
Prolongation FMEP
N FME-N
FSMA FME-FSMA
BNC FME-BNC
TNC FME.TNC
UHF FME-UHF
Mini-UHF FME-MUHF
Elbow-MUHF FME-EMUHF
Elbow-BNC FME-EBNC
Elbow-TNC FME-ETNC
SMA FME-SMA
For further information about other types of FME-cables please compare the cable data sheets under
accessories in our catalogue.
INSTALLATION
CX-mount antenna types can be mounted anywhere on the car, however,
roof top mounting is always recommended. Mounting can take place
exclusively with access from the outside when drilling an 18 mm dia. hole.
Mounting can take placefrom the inside by drilling a 14 mm dia. hole, in
which case the bottom plastic ring of the packing gasket should be
removedwith a sharp cutter.
A good contact surface on the inside of the car body must always be
ensured, thus enabling the base plate to get in directcontact with the metal
parts of the car, which is of utmost importance for proper performance of
the antenna.
When cleaning the car in car-washing machines, the whip is easily removed
using a fork spanner.
The whip is refitted again byscrewing it onto the thread stud and tightening
it lightly with the spanner. As the CX-mount is internally equipped with a
bendable section, the antennas can always be adjusted to an upright
positionindependent of the tilt angle of the installation spot (up to 30° tilt).
1. INSTALLATION DIMENSIONS