Ta-tm 5 series – Asus TM-58 User Manual
Page 2
T A / T M 5 S e r i e s
T A / T M 5 S e r i e s
T A / T M 5 S e r i e s
T A / T M 5 S e r i e s
T A / T M 5 S e r i e s
TA-TM 5
Series
Removing the side covers and front bezel
Removing the side covers and front bezel
Removing the side covers and front bezel
Removing the side covers and front bezel
Removing the side covers and front bezel
1
1
1
1
1
2
2
2
2
2
3
3
3
3
3
Remove the screws on
the rear panel.
Push the side cover towards
the rear panel.
Repeat steps 1 and 2 to
remove the other side cover
Release the side
tabs that secure
the front bezel to
the chassis.
Swing the front bezel in the
direction of the arrow.
Unhook the hinge-like tabs. Set the
front bezel aside.
4
4
4
4
4
Installing the power supply unit (PSU)
Installing the power supply unit (PSU)
Installing the power supply unit (PSU)
Installing the power supply unit (PSU)
Installing the power supply unit (PSU)
2
2
2
2
2
Locate the PSU slot.
1
1
1
1
1
3
3
3
3
3
Slide the PSU into the slot
until it snugly fits the
metal rail.
Secure with screws.
Installing an optical disk drive (ODD)
Installing an optical disk drive (ODD)
Installing an optical disk drive (ODD)
Installing an optical disk drive (ODD)
Installing an optical disk drive (ODD)
2
2
2
2
2
1
1
1
1
1
Insert the ODD into the
bay.
Align the ODD holes with
the bay holes, then secure
the ODD with screws on
both sides of the bay.
Release the lock tabs on
the front bezel to
disengage the drive cover.
3
3
3
3
3
Installing a hard disk drive (HDD)
Installing a hard disk drive (HDD)
Installing a hard disk drive (HDD)
Installing a hard disk drive (HDD)
Installing a hard disk drive (HDD)
2
2
2
2
2
1.
Insert the HDD into
the bay.
2.
Align the HDD hole
with the bay hole.
3.
Secure the HDD with
a screw on both
sides of the bay.
1
1
1
1
1
3
3
3
3
3
Installing a floppy disk drive (FDD)
Installing a floppy disk drive (FDD)
Installing a floppy disk drive (FDD)
Installing a floppy disk drive (FDD)
Installing a floppy disk drive (FDD)
2
2
2
2
2
1
1
1
1
1
3
3
3
3
3
Insert the FDD into the
bay. Make sure the FDD
holes align with the
chassis holes.
Using a screwdriver, push
the knock-down metal
cover in and out of the
chassis until it is removed.
Secure the FDD with
screws.
Release the lock tabs on the
front bezel to disengage the
drive cover.
4
4
4
4
4
Installing an expansion card
Installing an expansion card
Installing an expansion card
Installing an expansion card
Installing an expansion card
2
2
2
2
2
1
1
1
1
1
3
3
3
3
3
Choose the slot you want to
use. Remove the metal cover
on the rear panel.
Remove the screws
securing the
bracket to the
chassis. Remove
the expansion slot
bracket.
Lay the chassis on a flat,
stable surface. Align the
card connector with the
slot, then press firmly
until the card is
completely seated on the
slot.
Replace the expansion slot
bracket and secure it with
the screws you removed
earlier.
4
4
4
4
4
Reinstalling the side cover and front bezel
Reinstalling the side cover and front bezel
Reinstalling the side cover and front bezel
Reinstalling the side cover and front bezel
Reinstalling the side cover and front bezel
Hook the
hinge-like tabs to
the holes on the
chassis. Swing the
front bezel in the
direction of the
arrow and push to
secure the front
bezel to the
chassis.
Standard Model
Standard Model
Standard Model
Standard Model
Standard Model
1
1
1
1
1
2
2
2
2
2
Push the side cover towards
the front bezel.
Drive screws on the
rear panel.
3
3
3
3
3