Asus MEZ-VM - Manual (Page 16)

16 ASUS MEZ-VM User’s Manual
Jumpers
III. H/W SETUP
III. HARDWARE SETUP
4. CPU Bus Frequency Selector (FS0, FS1, FS2, FS3, FS4)
This option tells the clock generator what frequency to send to the CPU, DRAM, and
440ZX AGPset. This allows the selection of the CPU’s External frequency (or BUS
Clock). The BUS Clock multiplied by the BUS Ratio equals the CPU’s Internal fre-
quency (the advertised CPU speed).
5. CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3)
This option sets the frequency multiple between the Internal frequency of the
CPU and the CPU’s External frequency. These must be set in conjunction with the
CPU Bus Frequency.
NOTES: Overclocking your processor is not recommended. It may result in a slower
speed. Voltage Regulator Output Selection (VID) is not needed for the Pentium II/Celeron
processor because it sends a VID signal directly to the onboard power controller.
Set the jumpers by the Internal speed of your processor as follows:
(CPU BUS Freq.) (Freq. Multiple)
Intel CPU Model Freq. Ratio BUS F. FS0 FS1 FS2 FS3 FS4 BF3 BF2 BF1 BF0
Celeron (PPGA) 366MHz 5.5x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [2-3] [1-2] [1-2] [1-2]
Celeron (PPGA) 333MHz 5.0x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [2-3] [1-2] [1-2] [2-3]
Celeron (PPGA) 300MHz 4.5x 66MHz [1-2] [1-2] [2-3] [2-3] [2-3] [2-3] [1-2] [2-3] [1-2]
MEZ-VM CPU Settings
0 1
CPU Core:Bus Frequency Multiple
5.5x(11/2)
1
2
3
BF3 BF2 BF1 BF0
5.0x(5/1)
1
2
3
BF3 BF2 BF1 BF0
6.0x(6/1)
1
2
3
BF3 BF2 BF1 BF0
4.5x(9/2)
1
2
3
BF3 BF2 BF1 BF0
4.0x(4/1)
1
2
3
BF3 BF2 BF1 BF0
3.5x(7/2)
1
2
3
BF3 BF2 BF1 BF0
3.0x(3/1)
1
2
3
BF3 BF2 BF1 BF0
CPU Bus Frequency
112.0MHz
37.3MHz
115.0MHz
38.3MHz
120.0MHz
40.0MHz
124.0MHz
31.0MHz
133.0MHz
44.3MHz
124.0MHz
41.3MHz
133.0MHz
33.3MHz
CPU
PCI
FS0
FS1
FS2
FS3
FS4
1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3
110.0MHz
36.7MHz
105.0MHz
35.0MHz
75.0MHz
37.5MHz 83.0MHz
41.6MHz 100.3MHz
33.4MHz
103.0MHz
34.3MHz
66.8MHz
33.4MHz CPU
PCI
FS0
FS1
FS2
FS3
FS4
1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3
WARNING! Frequencies above 100MHz exceed the specifications for the on-
board Intel Chipset and are not guaranteed to be stable. PCI frequencies above
33MHz exceed the specifications for PCI cards and are not guaranteed to be stable.