Wash cycles and options, Wash options, Table of wash cycles – Hotpoint Ariston AQD1070D 69 User Manual
Page 9
EN
9
9
Wash options
Super Wash
This option offers a high-
performance wash due to
the greater quantity of water
used in the initial phase
of the cycle, and due to
the increased wash cycle
duration, is particularly useful
for the removal of stubborn
stains. It can be used with or
without bleach. If you desire
bleaching, insert the extra
tray compartment (3) into
compartment 1. When pouring in the bleach, be careful
not to exceed the “max” level marked on the central pivot
(see figure).
To bleach laundry without carrying out a full
wash cycle, pour the bleach into the extra compartment 3,
select the “Rinse” cycle and activate the “Super Wash”
option .
! It cannot be used in conjunction with ,
,
,
, , ,
,
,
,
,
.
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal residual detergent removal is
guaranteed. It is particularly useful for skin which is
sensitive to detergents. We recommend this option is used
with a full load of washing, or when a large amount of
detergent is required.
! It cannot be used in conjunction with
,
,
,
, ,
,
,
.
Easy Iron
By selecting this option, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the Washer-dryer drum will
rotate slowly; the “Easy Iron” and START/PAUSE indicator
lights will flash. To end the cycle press the START/PAUSE
button or the “Easy Iron” button.
! It cannot be used in conjunction with
,
,
,
,
, ,
,
,
.
Note: If you also want to run the drying cycle, this option is
enabled only if combined with level “Iron”.
Time Saver
If you select this option, the wash cycle duration will be
reduced by up to 50%, depending on the selected cycle,
thereby guaranteeing simultaneous water and energy
saving. Use this cycle for lightly soiled garments.
! It cannot be used in conjunction with ,
,
,
, ,
,
, ,
,
,
.
3
1
2
(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.
Wash cycles and options
Table of wash cycles
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle
with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle
with a temperature of 40°C.
Icon Description of the wash cycle
Max. temp.
(°C)
Max.
speed
(rpm)
Drying
Detergent and additives
Max.
load
(kg)
Cycle
duration
Pre-
wash
Wash Bleach
Fabric
softener
Cotton Coloureds (2): lightly soiled whites and delicate colours.
40°
1600
-
10
Synthetics Resistant
60°
800
-
5
Whites
60°
1600
-
-
6
Coloureds
40°
1600
-
6
Darks
30°
800
-
-
6
Wool Platinum Care: for wool, cashmere, etc.
40°
800
-
-
2,5
Ultradelicates
30°
0
-
-
1
Anti Allergy
60°
1600
-
-
6
Rinse
-
1600
-
-
10
Spin and Pump out
-
1600
-
-
-
-
10
Wash&Dry
30°
1600
-
-
1
Drying Cottons
-
-
-
-
-
-
7
Drying Wool
-
-
-
-
-
-
2,5
Drying Synthetics
-
-
-
-
-
-
5
Cotton Hygiene Prewash
(Add detergent to the relevant compartment).
90°
1600
-
10
Cotton Whites (1): heavily soiled whites and resistant colours.
60°
(Max. 90°C)
1600
-
10
(*) The duration of the wash cycles can be checked on the display
.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as
water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.