C2G 22391 One-Console KVM Switches - Manual (Page 11)

20
Hot-key commands
Hot-key command is a short keyboard sequence to select a computer,
to activate computer scan, etc. The KVM Switch interprets
keystrokes for hot-keys all the time. A hot-key sequence starts with
two left <CTRL> keystrokes followed by one or two more keystrokes.
A built-in buzzer generates a high-pitch beep for correct hot-key
command; otherwise, one low-pitch beep for error and the bad key
sequence will not be forwarded to the selected computer.
The short form hot-key menu can be turned on as an OSD function
(<F4>:more\Hotkey Menu) every time the left <CTRL> key is pressed
twice.
L-CTRL: is the <CTRL> key located at the left side of the
keyboard.
1~8/A~H: are the number keys '1' ~ '8' at the upper row of the
keyboard and character keys 'A' ~ 'H' case
insensitive. Do not use the keypad at the right of
the keyboard.
J To select a computer by hot-key command, you must know its port
address, which is determined by the KVM Switch connection.
For a computer connected to a Master, its address is represented
by the PC port label (1~8 or A~H). For a computer connected to
a Slave, two characters represent its address. The first character
is the port address of the Master unit (1~8) and the second one is
the port address of the Slave (1~8 or A~H). Please note that
only Master's 'PC 1' ~'PC 8' ports can be connected to a Slave.
Left Ctrl + left Ctrl + 7
Selects a computer connected to port 7 of the Master.
Left Ctrl + left Ctrl + 6 + C
Selects a computer connected to port C of a Slave connected
to port 6 of the Master.
J To start Auto Scan, automatically scan power-on computers one
by one at a fixed interval:
left Ctrl + left Ctrl + F 1
When Auto Scan detects any keyboard or mouse activity, it
21
suspends the scanning till activity stops; it then resumes with the
next computer in sequence. The length of the Auto Scan interval
(Scan Rate) is adjustable, see below. To abort the Auto Scan
mode, press the left Ctrl key twice.
Note: For OSD models, Scan Type determines whether eye mark is
necessary during Auto Scan.
J Manual Scan enables you to manually switch back and forth
between power-on computers.
left Ctrl + left Ctrl + F2
Press ↑ ↑ ↑ ↑ or ↓ ↓ ↓ ↓ to select the previous or the next computer in
sequence. And, press any other key to abort the Manual Scan.
Note: For OSD models, Scan Type determines whether eye mark is
necessary during Manual Scan.
J To adjust Scan Rate which sets the duration before switching to
the next computer in Auto Scan:
left Ctrl + left Ctrl + F3
The KVM Switch sends one to four beeps indicating scan interval of
3, 8, 15 and 30 seconds respectively.
J To adjust keyboard typematic rate (characters/sec), this setting
over-rides that of BIOS and any operating system:
left Ctrl + left Ctrl + F4
The KVM Switch generates 1 to 4 beeps corresponding to 10, 15,
20 and 30 characters/sec respectively.
J Audio Stick
An optional multimedia module can be LINKed to the back of each
KVM Switch for selecting microphone and stereo speaker signals.
There are two options for Audio Stick: ON and Off. When set to
'On', audio selection follows computer selection. When set to 'Off',
audio selection stops following computer selection. It is useful if
you want to listen to a particular computer's audio signal while
operating other computers.
left Ctrl + left Ctrl + F5
The KVM Switch generates 1 or 2 beeps corresponding to On and
Off respectively.