Extron Electronics CIA114F5 Setup Guide User Manual
Preparation, Connections, Pre-installation testing and setup
This guide provides instructions for an experienced installer to set up
and operate the CIA111, CIA114, and CIA114F5 computer
video interfaces.
N
The CIA111 (2-gang wide) and CIA114
(1-gang wide) are mounted in standard
wall boxes. The CIA114F5 is mounted in a
Steel City
®
665 floor box.
Preparation
Step 1 — Wall preparation
N
Use a wall box with a depth of at least 2.5
" (6.4 cm).
a
. Place the wall box against the installation surface, and
mark the opening guidelines.
T
Use a level when you mark the opening.
b
. Cut out the material from the marked area.
c
. Secure the wall box, leaving the front edge flush with the
surface.
d
. Run all required cables (see steps 2, 3, and 4) and secure them with cable clamps.
Step 2 — Remove power
Turn off or disconnect all equipment power sources.
Connections
Step 3
— Inputs
•
Connect a VGA to UXGA source to the front panel Computer Input connector.
•
Connect a computer audio source to the front panel Audio Input mini jack.
Step 4 — Outputs
•
Connect these five rear panel BNC connectors to the display’s
RGB input.
•
Connect an audio output device
to the rear panel Audio direct
insertion connector. Wire the
connector as shown at right.
C
For unbalanced audio,
connect the sleeves to the
ground contact. DO NOT connect the sleeve(s) to the negative (-) contacts.
N
The unbalanced output wiring scheme on this output connector is different from most other
Extron audio devices. Double check if you are not sure.
•
If desired, connect a local monitor to the interface’s front panel Monitor Output
connector.
Pre-Installation Testing and Setup
Step 5 — Power
Wire the 2-pole captive screw connector for the included external 9 VDC power
supply as shown at right. The power indicator lights.
C
Voltage polarity is critical. Reversing the polarity can damage the
power supply and the CIA. The power cord’s positive lead has a
red heat shrink, or you can check the power supply output with a voltmeter.
Setup Guide — CIA111, CIA 114, and CIA114F5
AUDIO INPUT
COMPUTER INPUT
MONITOR OUTPUT
Unbalanced Output
Tip
NO GROUND HERE
Sleeve (s)
Tip
NO GROUND HERE
Balanced Output
Tip
Ring
Sleeve (s)
Tip
Ring
L
R
A
UDIO
L
R
A
UDIO
Do not tin
the wires!
+ –
Wall Stud
Cable
Clamp
Screws
or Nails
Cable
Wall opening
is flush with
edge of box.
Step 6 — DIP switches
1 Image Shift control
• On —
The front panel Image Shift button is enabled (default).
• Off —
The Image Shift button is disabled.
2 Output sync format (sync on green)
• On —
The interface outputs RGsB video.
•
Off — The interface outputs RGBS or RGBHV video (default), as selected by switch 3.
3 Output sync format (RGBS or RGBHV)
• On —
The interface outputs RGBHV video (default).
• Off —
The interface outputs RGBS video.
4 No Monitor at Power Up
• On —
The interface powers up with No Monitor enabled (default).
• Off —
The interface powers up with No Monitor disabled.
5 Auto Power Disable
• On —
The interface powers up unless you disconnect the power cable.
• Off —
The interface powers up when it senses an input sync signal and turns off when
the sync is removed (default).
6 NOT USED
Step 7
— Sharpness
Use a screwdriver to turn this control clockwise to increase the sharpness setting or
counterclockwise to decrease the sharpness setting.
Installation
Step 8 — Mounting and final power
a
. At the power outlet, unplug the power supply.
b.
Mount the interface into the wall box or floor box.
c
. At the power outlet, reconnect the power supply.
Operation
No Monitor (monitor emulation) button and LED —
If you are not using a local
monitor, press this button to turn on the monitor emulation feature, providing
proper ID bit termination on the local monitor output.
On —
ID bits 4 and 11 are tied to ground.
Off —
ID bits 4 and 11 are unterminated.
The LED lights to indicate that the feature is on.
Image Shift button —
While viewing the displayed image, press this rocker button to
adjust the horizontal positioning of the image on screen. Pressing the left (lower
on CIA114F5) side of the button moves the image to the left and pressing the right
(upper on CIA114F5) side of the button moves it to the right.
68-809-50
Rev. A
04 09
Setup Guide — CIA111, CIA114, and CIA114F5
IMAGE SHIFT
NO MONITOR