Extron Electronics DVI 201xi Tx Quick Start Guide - Manual

This card provides quick start instructions for an experienced
installer to set up and operate the DVI 201xi Tx.
Refer to www.extron.com for the complete user’s guide.
Step 1
Turn off all equipment or disconnect from power sources. Mount the
transmitter and receiver as required.
Step 2
Choose a receiver that is compatible with the DVI 201xi Tx.
Step 3
Determine how the source device will obtain the EDID information
and select one of the following choices.
Procedure A:
To capture the EDID of a desired display and store it in
the EDID Minder for future use:
i
. Connect the display to the local monitor output of
the transmitter.
ii . Power on the transmitter and the local monitor.
iii . Configure the DDC switches as shown in the figure
at right.
iv . Press and release the EDID "Store" button (see the
figure at right). The rear panel LED turns amber
while the EDID information is read and stored from
the local monitor. Afterwards, the LED turns green.
v . Power off and disconnect the display from the
transmitter.
vi . Connect the transmitter to the receiver.
vii . Connect a source device to the transmitter.
viii . Connect a display device to the receiver and, if required, a local
monitor to the transmitter.
ix . Power on the display device(s), the transmitter, and the receiver.
x . Power on the source device.
Procedure B: To use the default EDID:
i . Configure the DDC switches as shown in the figure
at right.
ii . Connect a source device to the transmitter.
iii . Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
iv . Connect the transmitter and receiver.
v . Power on the transmitter, receiver, and display devices.
vi . Power on the source device.
ON
1 2 3
ON
OFF
DEF
AUL
T EDID
EDID MINDER REMOTE DDC
STORE
EDID
ON
1 2 3
ON
OFF
DEF
AUL
T EDID
EDID MINDER REMOTE DDC
Quick Start Guide — DVI 201xi Tx
68-1645-50
Rev. A
12 08
Procedure C: To use DDC pass-through routed to the local monitor:
i . Configure the DDC switches as shown in the figure at right.
ii . Connect a source device to the transmitter.
iii . Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
iv . Connect the transmitter and receiver.
v . Power on the transmitter, receiver, and local monitor.
vi . Power on the source device.
vii . Power on the source device.
Procedure D: To use DDC pass-through routed to the remote
display:
i
. Configure the DDC switches as shown in the figure at right.
ii . Connect a source device to the transmitter.
iii . Connect a display device to the receiver and, if
required, a local monitor to the transmitter.
iv . Connect the transmitter and receiver.
v . Power on the transmitter, receiver, and display
devices.
vi . Power on the source device.
Step 4
The DVI 201xi Tx transmits single link DVI-D (1024x768 or
720p @ 60 Hz up to 200'; 1920x1200 or 1080p @ 60 Hz up to 100') over
two CAT 5/5e/6/7 twisted pair cables.
ON
1 2 3
ON
OFF
DEF
AUL
T EDID
EDID MINDER REMOTE DDC
ON
1 2 3
ON
OFF
DEF
AUL
T EDID
EDID MINDER REMOTE DDC
1
2
12V
0.4A MA X POWE R DVI-D INPU
T LOCAL MONITOR OUTPUT
OUTPUT
S DO NO T
CONNEC T
OUTPUTS TO LAN
SN XXXXXXXX E XXXXX 00/0 0
DVI DL TX
STO RE ED ID
Tx Rx CO NT RO L
PAS S T HR U
ON
1 2 3 ON
OF F
DE FA UL T EDID
EDID MINDE
R
REMO TE DDC
PC w/ Dual Link
DVI Output
Local Monitor
Extron
DVI 201xi Tx
DVI Transmitter
Extron
DVI 201 Rx
Receiver
Projector
Twisted Pair
Cables (2) 100'
RS-232
DVI 200 RX SERIE
S
RS-232 PA SS THRU
Tx Rx
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX