Extron Electronics FOX DA8 Plus Setup Guide User Manual
Fox da8 plus • setup guide, Installation, Step 1 — mounting
FOX DA8 Plus • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron FOX DA8 Plus fiber optic distribution amplifier. See the
on the next page.
WARNING:
This unit outputs continuous invisible light, which may be harmful to the eyes;
use with caution. For additional safety, plug the attached dust caps into the
optical transceivers when the fiber optic cable is unplugged.
Installation
Step 1 — Mounting
Turn off or disconnect the power sources to all equipment and mount the FOX DA8 Plus as desired.
Step 2 — Configuration
Set the rear panel DA configuration switch to configure the unit as either one 8-output DA, two 4-output DAs, or four 2-output DAs.
See the drawing below.
FOX DA8 Plus
100-240V 0.3A
OPTICAL OUTPUTS
A
B
C
D
OUT IN
1
OUT
IN
3
OUT
IN
5
OUT
IN
7
(1)1x8
(2)1x4
(4)1x2
50/60 Hz
RS-232
Tx Rx
OUT
N/A
4
OUT
N/A
6
OUT
N/A
8
OUT
N/A
2
FOX DA8 Plus
100-240V 0.3A
OPTICAL OUTPUTS
A
B
C
D
OUT IN
1
OUT IN
3
OUT IN
5
OUT
IN
7
(1)1x8
(2)1x4
(4)1x2
50/60 Hz
RS-232
Tx Rx
OUT
N/A
4
OUT
N/A
6
OUT
N/A
8
OUT
N/A
2
FOX DA8 Plus
100-240V 0.3A
OPTICAL OUTPUTS
A
B
C
D
OUT IN
1
OUT IN
3
OUT IN
5
OUT IN
7
(1)1x8
(2)1x4
(4)1x2
50/60 Hz
RS-232
Tx Rx
OUT N/A
4
OUT N/A
6
OUT N/A
8
OUT N/A
2
Rx
Tx
Tx
Tx
Tx
Tx
Tx
Tx
Rx Rx Rx Rx Rx Rx Rx
Rx Rx Rx Rx Rx Rx Rx Rx
Rx Rx Rx Rx Rx Rx Rx Rx
C
Group: A
Group: A
C
D
B
One 8-output DA
Two 4-output DAs
(Groups A and C)
Four 2-output DAs
(Groups A through D)
(1)1x8
(2)1x4
(4)1x2
(1)1x8
(2)1x4
(4)1x2
(1)1x8
(2)1x4
(4)1x2
Step 3 — Optical Inputs
OPTICAL
2*
1
LINK
LINK
OPTICAL
1
2*
*
OPTIONAL FOR
RETURN DATA
LINK
LINK
Transmitter
Receiver
DA
3
4
A
OUT IN
1
Connect a fiber optic transmitter (or the maximum number of inputs as determined by the DA configuration switch
position in step 2) to the FOX DA8 Plus rear panel input connector.
NOTES:
•
Inputs 3, 5, and 7 (the right-hand connector on those transceiver blocks) are functional only when
selected as an input using the DA configuration switch.
•
The right-hand connector for transceiver blocks 2, 4, 6, and 8 can never be functional.
•
Singlemode and multimode devices are not interchangeable. Ensure that you connect transmitting and
receiving devices that are compatible with the FOX DA8 Plus.
•
Ensure that you use the proper fiber cable for your system. Typically, singlemode fiber has a yellow jacket
and multimode cable has an orange or aqua jacket.
Step 4 — Optical Outputs
Connect up to eight fiber cables between the FOX DA Output LC connectors (the left-hand connector on each
transceiver block) and compatible receivers.
Step 5 — Remote Control Connections
Do not tin the wires!
Controlling
Device
Gnd ( )
Rx
Tx
Ground ( )
Receive (Rx)
Transmit (Tx)
Bidirectional
RS-232
Tx Rx
Function
Pin
TX
RX
Gnd
Transmit data
Receive data
Signal ground
z
Connect a host device to the rear panel RS-232 port.
See the drawing at right to make the connection
z
Connect a host device to the front panel Config(uration) port,
a mini USB port.
Step 6 — Power
Use a standard IEC power cord to connect the FOX DA8 Plus power connector
and a 100 VAC to 240 VAC, 50-60 Hz power source.