Extron Electronics HAE 100 Setup Guide - Manual (Page 2)

2
HAE 100 • Setup Guide (Continued)
Extron USA - West
Headquarters
+800.633.9876
Inside USA/Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA/Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Output LEDs
z
Signal — This LED lights when the unit is providing video on the HDMI output connector.
z
HDCP — This LED lights when the HDMI output signal is encrypted with HDCP.
z
Analog — This LED lights when the unit is providing analog audio from the 3.5 mm,
5-pole captive screw output connector.
z
S/PDIF — This LED lights when the unit is providing digital audio from the S/PDIF RCA
output connector.
Config Port
If necessary, connect a control PC to this port using a USB cable. Use this port to update firmware
and check the status of various functions.
Rear Panel Overview
Audio Format Switch
A toggle switch located on the rear panel is used for selecting the audio format that the
HAE 100 will extract from the HDMI signal. The position of this toggle switch also governs the
EDID presented to the source device connected to the input of the HAE 100.
z
Set this switch to the Analog (up) position to extract 2-channel stereo audio from the
HDMI input signal.
NOTE: If the embedded audio is 2-channel LPCM, the audio can be output from the
analog output and the S/PDIF output simultaneously.
z
Set this switch to the S/PDIF (down) position to extract digital S/PDIF audio from the
HDMI input signal.
Configuration DIP Switches
A 2-pole DIP switch located on the rear panel is used to configure the following features.
z
EDID Store — Set this switch to the On (up) position to enable the EDID store function
(see the "EDID Store Button and LED" section below). Set this switch to the Off (down)
position to disable the EDID store function.
NOTE: The EDID Store LED is unlit when this function is disabled.
z
HDMI Output Audio — Set this switch to the On (up) position to send audio to the
HDMI output, the Analog output, and/or the S/PDIF output simultaneously. Set this switch
to the Off (down) position to send audio only to the analog output and/or S/PDIF output.
EDID Store Button and LED
A recessed push-button is used to store EDID from a display that is connected to the HDMI output. With the EDID Store
switch set to the On (up) position, press the recessed push-button to learn and store EDID information.
Use the LED to determine the status of the EDID storage.
z
Off — EDID storage is disabled. Factory default EDID is being used.
z
Red — EDID storage is enabled, but external EDID has not been stored. Factory default EDID is being used.
z
Green — EDID storage is enabled and external EDID is stored.
z
Amber — EDID storage is enabled and EDID is being loaded. The LED turns green when stored.
Mount the HAE 100
If necessary, mount the HAE 100. For mounting information, see the HAE 100 User Guide.
68-2027-50
Rev. A
02 11
SIGNAL
OUTPUT
HDCP
ANALOG
S/PDIF
HDMI OUTPUT AUDIO
ON
ON
OFF
1 2
EDID
STORE
S/PDIF ANALOG
AUDIO
FORMAT
L R
CONFIG