Extron Electronics DTP T UWP 232_332 D Setup Guide User Manual

Installation, Step 1 — disconnect power, Step 2 — prepare the mounting surface

Advertising
background image

IMPO

RTAN

T:

Go to ww

w.extr

on.com

for the complete

user guide

, installation instructions,

and

specifications bef

ore connecting the

product to the po

wer sour

ce.

DTP T HWP/UWP D 232/332 D • Setup Guide

This setup guide provides instructions for an experienced installer to set up and operate the
Extron DTP T HWP D and DTP T UWP D family of wallplate extenders.

Installation

Step 1 — Disconnect Power

Disconnect all equipment power sources.

Step 2 — Prepare the Mounting Surface

ATTENTION:

Installation and service must be performed by authorized
personnel only.

The installation shall be in accordance with applicable
provisions of the National Electrical Code and any local
electrical codes.

NOTE:

Use a wall box with a depth of at least 3.0 inches

(7.6 cm). Alternatively, the included mud ring (MR 200)
can be used. For more information, see the full product
user guide at

www.extron.com

.

a.

Place the wall box against the installation surface and mark the
opening guidelines.

TIP:

Use a level to mark the opening.

b.

Cut out the material from the marked area.

c.

Secure the wall box to the wall stud with 10-penny nails or #8 or #10 screws, leaving the front edge flush with the
surface.

d.

Run all required cables (see steps 3, 4, and 5) and secure them with cable clamps.

TIP:

In order to fit the unit in the junction box, do not

install boots on TP cables and RJ-45 connectors.

Extron

DTP T UWP 232/332 D

Signal Output

Cable

Cable

Clamp

Decora Faceplate

Screws or

Nails

Wall opening is

flush with edge of box.

Wall Stud

AUT

O S

W

CONF

IG

IR

OU

T

HDM

I IN

AUDI

O I

N

G

S

HDCP

1

AUDI

O I

N

VGA

IN

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

S

G

HDCP

1

HDMI IN

AUDIO IN

HDCP

1

2

AUTO SW

CONFIG

IR OUT

HDMI IN

AUDIO IN

S

G

HDCP

1

AUDIO IN

VGA IN

TLP 1000TV

IPCP 505

IN1608

DTP HDMI 230 Rx

Projector

100-240V ~ -- A MAX

1

2

CONFIGURABLE

HDMI

HDMI

5

6

7

8

C

RS-232 IR

RS-232

IR

Tx Rx

Tx Rx

G

Tx Rx

Tx Rx

G

Tx Rx

Tx Rx

G

HDMI

A

B

3

4

INPUTS

OUTPUTS

Tx Rx

RS-232

G

LAN

2x25W(8Ω)/2x50W(4Ω)

RESET

AUDIO INPUTS

OUTPUTS

REMOTE

L

L

1

R

R

L 2

R

L

3

R

CLASS 2 WIRING

L

4

R

L

5

R

+48V

+48V

1

2

L

R

VARIABLE

IN1608 SA

2

MIC/LINE

L

6

R

SIG LINK

DTP IN

SIG LINK

DTP IN

SIG LINK

DTP OUT

50/60 Hz

RS-232

IR

OVER DTP

OVER DTP

OVER DTP

AMPLIFIED OUTPUT

VOLUME

SCALING PRESENTATION SWITCHER

IN1608

INPUTS

1

HDCP

SIGNAL

OUTPUTS

ENTER

MENU

Extron

2

3

4

5

6

7

8

A

B

C

INPUTS

1 2 3 4 5 6 7 8

CONFIG

Extron

DTP T UWP 232 D Tx

Transmitter

Extron

DTP T HWP 232 D Tx

Transmitter

Ethernet

A Typical DTP T HWP 232 D and DTP T UWP 232 D Application

Network

L

R

POWER

12V
0.7A MAX

AUDIO

SIG LINK

DTP IN

OUTPUTS

XTP DTP 24 Cable

230 '

XTP DTP 24 Cable

230 '

XTP DTP 24 Cable

230 '

HDMI

1

2

3

4

5

6

7

8

100

LINK

ACT

COM

IR/S

TX

RX

TX

RX

RTS

CTS

R

5

1

6

2

7

3

8

4

RELAY

FLEX

I/O

5

1

6

2

3

1

4

2

eBUS

ACT LIMIT

OVER

SWITCHED

12VDC

3

1

4

OVER

2 LIMIT

IR

7

3

8

4

IPCP 505

Advertising
This manual is related to the following products: