Extron Electronics Fiber Matrix 6400 Input-Output Board User Manual
Removing the i/o board or blank panel, Installing the i/o board, Out in
68-1371-30
Rev. A 05 08
Fiber Matrix 6400 Input/Output Board
Installation Instructions
Removing the I/O board or blank panel
Remove an I/O board or blank panel as follows:
N
The I/O boards are hot-swappable. You do not need to power
down the switcher to remove an I/O board.
1
. For an I/O board, disconnect any connected cables.
2
. Rotate the left and right knurled knobs to completely loosen
the captive screws.
3
. Gently pull on the knurled knobs/captive screws to loosen
the board or panel from the backplane.
4
. Slide the board or panel out of the chassis (see the illustration
on the other side of this card).
C
Do not touch the electronic components or the connectors
on the backplane or on the circuit boards without being
electrically grounded. Handle circuit boards by their edges
only. ESD can damage ICs, even if you cannot feel, see, or
hear it.
5
. Place the removed board on an anti-static surface or in an
anti-static container.
Installing the I/O board
Install an I/O board as follows:
N
The I/O boards are hot-swappable. You do not need to power
down the switcher to install an I/O board.
C
Do not touch the electronic components or the connectors
on the backplane or on the circuit boards without being
electrically grounded. Handle circuit boards by their edges
only. ESD can damage ICs, even if you cannot feel, see, or
hear it.
1
. Orient the board to be installed so that transceiver module A
(fiber board) or input BNC A (SDI/HD-SDI board) is on the
left and transceiver module or output BNC H is on the right.
2
. Align the board with the left and right chassis guides (see the
illustration on the other side of this card).
3
. Gently slide the board into the enclosure. Slide the board
toward the front panel until it meets resistance.
4
. Gently seat the board in the backplane.
5
. Tighten the left and right knurled knobs/captive screws to
lock the board or panel in place.
N
If necessary, use a screwdriver to tighten the knurled knobs/
captive screws.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
www.extron.com
Fiber Matrix 6400 Input/Output Board
Installation Instructions (Continued)
100-240V 50/60H
z
1.2A MAX.
100-240V 50/60H
z
1.2A MAX.
REDUND
ANT
PRIMAR
Y
1 - 8
9 - 16
17 - 24
25 - 32
33 - 40
41 - 48
49 - 56
57 - 64
LAN
A
CT
LINK
RESE
T
ANAHEIM
, CA
PRIMAR
Y PO
WER SUPPL
Y
REDUND
ANT PO
WER SUPPL
Y
Align with Plastic Guides
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
OUT
IN
A
OUT
IN
B
OUT
IN
C
OUT
IN
D
OUT
IN
E
OUT
IN
F
OUT
IN
G
OUT
IN
H
IN
MUTI-R
AT
E SDI INPUTS
H
G
A
D
E
F
C
B
MUTI-R
AT
E SDI OUTPUTS
H
G
A
D
E
F
C
B