Extron Electronics ISM HDSDI Output Board User Manual
Ism hdsdi output board • setup guide, Caution, The extron
The Extron
®
ISM HDSDI is
a universal video and RGB
scaler board with HDSDI
output for the ISM 824.
It has a single BNC connector and a local audio
output. The board mounts in one of the four vertical expansion slots
(numbered 1 to 4) at the rear of the ISM 824. Refer to the ISM 824 User Guide,
To install an ISM HDSDI output board in the ISM 824 base unit:
1.
Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.
2.
Select an open slot at the rear, or take out a blank plate by removing the two
retaining screws (top and bottom), and lifting the plate away.
NOTE:
Retain and reuse the screws to secure the new output board in place.
Retain the blank plates. If a board is already installed in the desired slot,
remove the screws and carefully pull out the board.
3.
Holding the new board by the frame
,
align the front (non-connector end) of the
board with the top and bottom plastic
guides in the ISM 824. Slide the board in
carefully, keeping within the guides. Push
it into place firmly, and secure it with the
retained screws.
4.
If required, repeat steps 2 through 4
for any other output boards.
5.
Power on the ISM 824. The new output
board(s) is autodetected, and takes
approximately 30 seconds to initialize.
The 16 character LCD display indicates the new board type,
slot used, and counts down the initialization time. See inset
for example display of a new ISM HDSDI board installed in
slot #2, with 16 seconds left.
6.
Connect a suitable display device to the BNC connector. The output can be
configured via the front panel (see page 2) or by SIS
™
commands (see page 3).
7.
Insert a 5-pole captive screw connector into the local audio output connector
for balanced or unbalanced stereo output. Wire the connector as shown below.
1
100
- 240
50/6
0 Hz
1.2A
MAX.
1
2
3
4
5
6
7
8
2
1
2
3
4
5
6
7
8
1
2
1
INPUTS
OUTPUTS
R/R-
Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-
Y
G/Y
VID
B/C
B-Y
H/HV
V
PA
SS
TH
RU
INPUTS
RESET
LA
N
REMO
TE
RS232/RS422
A
C
T
LINK
OUTP
UT
VIDEO
SCALER
70-54
5-01
3
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNI
V.
SCALER
70-544-01
5
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PA
SS
TH
RU
70-547-01
8
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
Extron
ISM 824
Integration Scaling
Matrix Switcher
Align output board
with top and bottom
plastic guides.
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
7
SCAN
CONV
.
70-546-01
Example Output Board Installation
NOTE:
X!
= Input number, 0-8
X@
= Output number, 1-8
X1)
= Mode status, 1 = on, 0 = off
X2)
= Test pattern, 00 = off, 01 = color bars, 02 = 4:3/16:9 crosshatch, 03 = 4x4 crosshatch,
04 = split gray scale, 05 = ramp, 06 = alternating pixels, 07 = crop, 08 = 1.33 aspect,
09 = 1.78 aspect, 10 = 1.85 aspect, 11 = 2.35 aspect
X2!
= Output resolution, 17 = 720p, 18 = 1080i, 19 = 1080p
X2@
= Refresh rate, 1 = 50 Hz, 2 = 60 Hz, 7 = 24 Hz, 8 = 25 Hz, 9 = 30 Hz, 10 = 59.94 Hz
X5%
= Aspect ratio, 1 = 16:9, 0 = 4:3
ISM HDSDI Output Board • Setup Guide
New Univ HDSDI
Slot #2
16
ISM HDSDI
HD
SD
I
UNIVERSA
L
SCALE
R
HDSDI
L
R
Unbalanced Stereo Output
Balanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
L
R
Left
Right
Tip
Sleeve(s)
Tip
L
R
Left
Right
NO GROUND HERE.
NO GROUND HERE.
CAUTION:
For unbalanced audio, DO NOT connect the sleeves to the
negative contacts. Connect to center ground contact.