Extron Electronics MDA 5SV User’s Manual Rev. B - Manual

○
○
○
○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○
User’s Guide
MDA 5V, 5SV, 5A RCA • Installation MDA 5V, 5SV, 5A RCA • Installation
Introduction
3 2
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
© 2002 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.extron.com
Mini Distribution Amplifiers
68-614-01 Rev. B
Printed in the USA
08 02
VersaTools™ MDA 5V, 5SV,
5A RCA
The Extron MDA 5 Series of Mini Distribution Amplifiers (MDAs)
are a family of three video and audio distribution amplifiers. The
MDA ar e members of the Extron V ersaT ools™ line of basic
distribution amplifiers, switchers, and associated video
accessories.
The MDA 5V distributes buf fered composite video, the MDA 5SV
distributes buffer ed S-video (luminance (Y) and chrominance
(C)), and the MDA 5A RCA distributes amplified ster eo audio, on
RCA outputs.
The MDAs ship with external, desktop 12V power supplies,
which accept 100-240V AC input.
Installation
The MDA 5V , 5SV , and 5A RCA can be mounted on a rack shelf,
under a desk or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the MDA on a V ersaT ools 19"
1U Rack Shelf (Extron part # 60-190-20 ) (figure 1) or a standar d
Universal 1U Rack Shelf (Extron part # 60-190-01 ) (figure 2). On
the standard rack shelf, the MDA mounts in one of four locations
to the rear of the rack or in one of four locations to the fr ont of the
rack.
Figure 1 — Rack mounting the MDA 5V, 5SV, or 5A
RCA on the VersaTools shelf
1 . If feet were pr eviously installed on the bottom of the MDA,
remove them.
2 . Mount the MDA on the rack shelf, using two 4-40 x 3/16
screws in opposite (diagonal) corners to secur e the MDA to
the shelf.
3 . Install blank panel(s) or other unit(s) to the rack shelf.
4. Insert the shelf into the rack, aligning the holes in the shelf
with those of the rack.
5. Secure the shelf to the rack using the supplied machine
screws. This shelf can be mounted in the fr ont or in the rear
of the rack.
Only products in the V ersaT ools line can be mounted to a
VersaT ools shelf. Any 1U rack-mountable Extron pr oduct
can be mounted on the standard shelf.
Figure 2 — Mounting the MDA on the standard shelf
Furnitur e or projector mounting
Furniture mount or pr ojector mount the MDA using the optional
mounting kit (Part #70-212-01 , furniture, or 70-217-01 , projector )
as follows:
1 . Attach the mounting brackets to the MDA with the machine
screws pr ovided (figure 3).
Figure 3 — Desk and projector mounting the
MDA 5V, 5SV, or 5A RCA
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
General
Power ................................................ 100VAC to 240VAC, 50/60 Hz, 5 watts,
external, auto-switchable; to 12VDC,
1 A (max.) power supply. Product requires
0.4 A (max).
Temperature/humidity ................. Storage -40° to +158°F (-40° to +70°C) / 10%
to 90%, non-condensing
Operating +32° to +122°F (0° to +50°C) / 10%
to 90%, non-condensing
Rack mount ...................................... Yes, with optional 1U rack shelf, part #60-
190-01,
or the VersaTools rack shelf, part #60-190-20
Enclosure type ................................. Metal
Enclosure dimensions .................... 1.7" H x 4.3" W x 3.0" D (1U high, quarter
rack width)
4.2 cm H x 11.0 cm W x 7.6 cm D
(Depth excludes connectors and knobs.)
Product weight ................................ 0.7 lbs (0.3 kg)
Shipping weight .............................. 3 lbs (1.4 kg)
Vibration ........................................... ISTA/NSTA 1A in carton (International Safe
Transit Association)
Listings .............................................. UL, CUL
Compliances .................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ................................................. 30,000 hours
Warranty ........................................... 3 years parts and labor
Specifications are subject to change without notice.
DIS TRIB UT IO N AM PLI FIE R
DI STR IB UT ION A MP LIF IER
DIS TR IB UT IO N A MPL IFIER
MDA S ER IES DIST RIBU TIO N AM PLIF IER
DIS TRIB UTION A MP LIFIER
Ceiling
Digital Projector
Projector
Mounting
Bracket
MD A 5V PO W E R 15V .5A MAX
1 2
3 4
IN P U T
O U TP U T S
Mounting
Bolt
Projector Mounting Under Desk Mounting
(2) 4-40 x 3/16" screws
Use 2 mounting holes on
opposite corners
VersaT ools Rack Shelf
1/4 Rack Width False F ront
Face Plate
DI STR IB UT ION A MP LIF IE R
DI ST RI BU TIO N AM PL IF IE R
DIS TR IB UT IO N A MP LIF IE R