Extron Electronics MTP SW6 Setup Guide - Manual

IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
MTP SW6 • Setup Guide
This card provides quick start instructions for an experienced installer to set up and operate the MTP SW6 switcher.
Installation
Step 1 — Mounting
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
12345678
1 2 3 4 5 6
INPUT
PRE-PEAK
ON
OFF
OUTPUT
NOTE : If you are using Enhanced Skew-Free™ A/V cable,
use the TIA/EIA T568A standard only.
Turn off or disconnect all equipment power sources and mount the MTP switcher as required.
Step 2 — TP Inputs from the Transmitters
Terminate up to six TP cables as shown at right. Connect them between MTP transmitters
and the Input connectors (both ends need to match).
Step 3 — RS-232 Insert Connector
For bidirectional RS-232 data that is routed from a common source to the TP output
regardless of the selected input, plug a serial device into the RS-232 Insert connector.
NOTES:
• For the RS-232 insert to be available on the TP output, it must be enabled by issuing
the
E
1*1Lrpt
}
SIS command to the switcher (see the MTP SW6 User Manual).
• When the RS-232 insert is enabled, any content on the audio/RS-232 wire pair for the
TP input tied to the output is disabled.
Step 4 — TP Output to the Receiver
Terminate a TP cable as shown for step 2. Connect it between the Output connector and receiver
that is compatible with the transmitters.
NOTE: The input and all outputs should all be terminated using the same standard on both
ends of the cables.
Step 5 — Connect a Local Audio Device
Connect an audio device to the Mono Audio connector. Wire the connectors as shown at right.
ATTENTION: For unbalanced audio output, connect the sleeves to the ground contact. DO
NOT connect the sleeves to the negative (-) contacts.
Step 6 — Remote Connector (Optional)
Connect an RS-232 device OR a contact closure device, such as a KP 6 Keypad Remote Control.
NOTES:
• For RS-232 control, use a cable with ONLY pins 2, 3, and 5 connected.
• For contact closure control, use a cable with pins 2 and 3 NOT connected.
RS-232 communications protocols:
• 9600 baud • 8 data bits
• 1 stop bit, no parity • no flow control
For contact closure control, short the pin for the desired input to pin 5 to select that device. To
force an input to be always selected, leave the short in place.
NOTES:
• For contact closure control, auto switch mode must be off.
• Contact closure control overrides front panel input selections.
Receive (Rx)
Transmit (Tx)
Ground ( )
Bidirectional RS-232 Device
Ground ( )
Receive (Rx)
Transmit (Tx)
Rx
Tx
SP
ARE
Do not tin the wires!
REMOTE
1
MONO AUDIO
2
1
MONO AUDIO
2
Unbalanced Output
Balanced Output
Do not tin the wires!
Mono output 1-
Sleeve(s)
Mono output 1+
Mono output 2+
Mono output 2-
Sleeve(s)
Mono output 1
Mono output 2
NO GROUND.
NO GROUND.
Pin RS-232
Contact
Closure Function
1 — In #1 Input #1
2 TX — Transmit data
3 RX — Receive data
4 — In #2 Input #2
5 Gnd Gnd Ground
6 — In #3 Input #3
7 — In #4 Input #4
8 — In #5 Input #5
9 — In #6 Input #6