Extron Electronics MTP U R Series Setup Guide - Manual

IMPO
RTAN
T:
Go to www
.extron.com f
or the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
MTP U R Series • Setup Guide
RGB
DELAY
PEAKING LEVEL
MTP U R RSA SEQ
R
G
B SELECT
ADJUST
SIGNAL
AUDIO
RS-232
VID
Y/C
YUV
RGB
This card provides quick start instructions for an experienced installer to set up
and operate any of the MTP U R Series products.
JMP1
JMP3
JMP2
Default settings
(viewed from rear)
Pre-installation — Jumper Settings
The MTP U R has three jumpers located on the main board. JMP1 is RS-232 directional communication,
and JMP2 and JMP3 are for vertical and horizontal sync (respectively). By default JMP1 is bidirectional;
JMP2 and JMP3 are negative sync.
Installation
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert Twisted
Pair Wires
Pins:
12345678
RJ-45
Connector
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP U R as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP U R. Terminate the
cable as shown on the right, using the same standard (A or B) at both ends.
POWER
12V
0.5A MAX
CAT 7 INPUT
NOTE: If the input is labeled “CAT 7 Input”, only a CAT 7 cable should be used (that is, MTP C7 U R RSA SEQ model).
Step 3 — Connect Outputs
RGB
1
MONO AUDIO
2
VID
Y/C
B-Y Y R-Y
OUTPUTS
RS-232
Tx Rx SPACE
Attach the applicable output cables (video, audio, and RS-232), depending on the MTP U R model used.
• Composite video output connector — Connect to the single female BNC connector (VID) .
• S-video output connector — Connect to the 4-pin mini DIN connector (Y/C).
• Component video (MTP U R RSA SEQ model only) — Connect to the three female BNC
connectors (Y, R-Y, and B-Y).
• High resolution video output connector — Connect to the 15-pin HD connector (RGB).
• RS-232 connector — Connect a serial communications port to the upper 3.5 mm,
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected RS-232
Device Pins
MTP/HDMI U R
Pins
Spare
Spare
5-pole captive screw connector for bidirectional RS-232 communication (as shown).
• Audio connector (MTP U R RSA SEQ and MTP U R A models only) — Connect a suitable audio device
audio device to the lower 5-pole captive screw connector for mono audio output (as shown).
1
MONO AUDIO
2
1
MONO AUDIO
2
Unbalanced Output Balanced Output
Do not tin the wires!
Mono output 1-
Sleeve(s)
Mono output 1+
Mono output 2+
Mono output 2-
Sleeve(s)
Mono output 1
Mono output 2
NO GROUND.
NO GROUND.
Step 4 — Power
Plug the included external 12 VDC power supply into the 2-pole captive screw connector. Wire the
connector (see image
a on the right).
Grounding guidelines
Extron MTP U R products can be adversely affected by electrostatic discharge (ESD) if they are not
grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an
Extron MTP U R product in either of two ways:
• Ground the power input port — Insert one end of the grounding wire to the negative or ground pin on
the power input connector (see image
a on the right). Tie the other end of the wire to an earth ground.
• Ground the chassis — Use a connector hex nut as shown in image b the right. Tie the other end of
the wire to an earth ground.
If you have any questions about how to ground a product in a specific application, contact an Extron technical
support specialist.
a
Power Supply
Output Cord
SECTION A–A
Ridges Smooth
A A
POWER
12V
xA MAX
Tie
Wrap
Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
b