Extron Electronics RM 1 Installation User Manual
Rm 1 • installation guide, Overview, Preparing and installing the rm 1 mounting kit
Refer
to ww
w.ext
ron.c
om fo
r the
comp
lete
TLP P
ro 32
0m an
d TLP
Pro 5
20M u
ser g
uide
and in
stalla
tion i
nstru
ction
s befo
re
conn
ectin
g the
prod
uct to
the p
ower
sour
ce.
RM 1 • Installation Guide
Overview
This guide provides instructions for an experienced, professional installer to mount and install the Extron
TLP Pro 320M or TLP Pro 520M TouchLink
®
panel using the RM 1 rack mounting plate. This plate fits into a standard
19-inch equipment rack, with 3U of vertical space. For complete instructions about installing and calibrating the
TouchLink panel, see the TLP Pro 320M User Guide or the TLP Pro 520M User Guide at
.
ATTENTION: The installation shall be in accordance with the applicable provisions of National Electrical Code
ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16.
NOTE: The diagram below shows the TLP Pro 520M. The TLP Pro 320M is mounted in exactly the same way.
Preparing and Installing the RM 1 Mounting Kit
To mount the TLP Pro TouchLink
touchpanel in any standard 19-inch
equipment rack, follow these
instructions:
1.
If necessary, disconnect any cables
that are attached to the touchpanel.
2.
Run cables to the rack. Provide
some slack in the cable for installing
the touchpanel.
3.
Secure the RM 1 rack mounting
plate to the rack using the provided
#10-32 rack mount screws (
a
in
the figure to the right).
Mounting the Touchpanel
1.
Align the four mounting holes of
the wall plate adapter (one in each
corner) with the four mounting holes
on the RM 1.
2.
Use the four provided mounting
screws (#6-32 x 0.375 inches) to
secure the wall plate adapter to the nut inserts in the RM 1 (
b
in the figure to the right). Do not overtighten the
screws.
3.
Snap the touchpanel to the wall plate adapter (
c
in the figure to the right).
4.
Connect the cables to the back of the touchpanel. If necessary, carry out an initial calibration of the TouchLink
panel. For complete instructions about cabling and calibration, see the TLP Pro 320M User Guide or the
TLP Pro 520M User Guide at
68-2299-01 Rev. A
02 14
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2014 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners.
Wall Plate Adapter
Secure the RM 1 to
the rack with the four
#10-32 screws provided.
TLP PRO 520M
RM 1
TLP Pro 520M snaps onto
the wall plate adapter
(2 places on each side).
Secure the wall adapter plate to the
RM 1 with the provided screws (4).
3
2
1