Extron Electronics WMK 160 - Manual

1
The Extron
®
WMK 160 Wall Mount Kit is used for hanging WallVault ®
System AV products on a wall near a flat screen display or short throw projector.
The WMK 160 has a 17.3 x 16.5 x 2.75
inches (43.9 x 41.9 x 6.9
cm) enclosure, and a base plate on which to mount the switcher (for
example the PVS 405D) and the associated power supply, with room
for cable management.
In addition, an accessory device can be mounted on the base plate.
The cover has knockouts on three sides that allow external raceways
to be used where needed for cabling.
WARNING: Risk of Personal Injury. Maximum load for the
WMK 160 is 15 lbs (7 kg)
NOTE: The WMK 160 is to be used only with Extron UL listed
products.
The key components (base plate, cover, and PVS switcher mounting
plate) of the WMK 160 are shown in figure 1. Included in the kit are the
following:
(4) ¼-20 x 2" pan head bolts, (4) ¼" KapToggle ® assemblies,
(2) #14 x 1¾" self tapping metal/wood screws,
(4) cover screws.
Not shown but included are (3) 4-40 x ¼" screws, (2) tie wraps (15"),
(8) 4-40 x 3/16" screws (used to attach other Extron devices).
Figure 1. WMK 160 parts
(2) #14 x 1 3/4"
Self-tapping
Metal/Wood Screws
(4) 1/4-20 x 2"
Pan Head Bolts
(4) 1/4" KapToggle ®
Assemblies
(4) Cover Screws
(1) PoleVault Switcher
Mounting Plate
(1) WMK 160 Cover
(1) WMK 160 Base Plate
(2) #14 x
Self-
Meta
(4)
(4) 1/4"
Asse
(4) Cove
(1) Pol
Mou
K 160 Base Plat t e e e (1) WMK
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this furnishing.
When using this furnishing, basic precautions should always be followed, including the following:
DANGER: Risk of Electric Shock . Disconnect power to this furnishing before cleaning.
WARNING: Risk of Electric Shock. Devices used in this furnishing should be connected to a properly grounded outlet only.
See Grounding Instructions in the device manual.
WARNING: Risk of Personal Injury. Read and follow the steps below to reduce the risk of burns, fire, electric shock, or injury
to persons.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.
WMK 160 • Installation Guide
1. Always unplug devices installed in this furnishing from outlets before putting on or taking off parts.
2. Close supervision is necessary when this furnishing is used by, or near children, invalid, or disabled persons.
3. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by
the manufacturer.
4. Never operate a device in this furnishing if it is not working properly, if it has been dropped or damaged, or dropped into
water. Return the device used in this furnishing to a service center for examination and repair.
5. Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9. To disconnect the devices, turn all controls to the off position, then remove plugs from outlet.