Extron Electronics SS 200 - Manual

1 Extron • SS 200 Sync Processor • User’s Guide
Installation and Operation
Description
The SS 200 Sync Stabilizer interface will accept either a RGsB,
RGBS, or RGBHV signal, automatically strip off the sync on
Green or the sync on Red, Green and Blue, and output RGBHV/
RGBS through five BNC connectors and, simultaneously, through
a 15-pin VGA connector. The output will be restored sync with
proper timing as generated by Extron’s Advanced Digital Sync
Processing (ADSP™) technology. ADSP™ enables the SS 200
to be sync compatible with digital display devices, such as LCD
projectors, DLP displays, and Plasma-based displays.
The SS 200 comes with its own external desktop power supply
and a detachable bracket for mounting the unit to a projector
mount or other convenient surface.
______ Warning! The SS 200 can also be powered by a projector’s power
supply which has a 12VDC positive output. It is important to verify
that the projector power connector is actually positive 12VDC.
Front Panel
The front panel consists of an auto sync detect LED indicator
(lights green when sync is present), 5 BNC input connectors, a
Horizontal shift control knob, and 6 DIP switches.
Rear Panel
The rear panel consists 5 BNC output connectors, a 15-pin VGA
output connector, and a power input jack for the power supply.
Mounting Bracket
The included mounting bracket is attached to the SS 200 using
the 3 bracket screws. The SS 200 may then be attached to a
projector mount or some other secure surface by inserting the
mounting screw through the bracket’s slotted hole. Please refer
to the
Application Diagram Example on the last page.
Mounting templates for Thru Desk and Under Desk installations
(using optional brackets) are provided on pages 3 and 4.
Easy Setup Procedure
The following easy-to-follow steps describe the general
installation setup of the SS 200. See the
Application Diagram
Example.
SS 200
75/510 H-SHIFT SERR V. CORR HV OUT NEG
1. Turn the computer and monitor power Off.
2. If you will be using the computer’s monitor, disconnect the
computer’s local monitor cable from the computer’s video port
and attach the video cable to the 15-pin female VGA port on the
rear panel of the SS 200.
3. Connect your RGB input device to the SS 200’s front panel BNC
input connectors.*
4. Connect the BNC output cables from the SS 200’s rear panel to
the display device.*
5. Insert the round power plug of the desktop power supply into the
power input jack located on the rear panel of the SS 200. When
using a compatible power source from the projector, verify that it
is 12VDC positive (please see warning on previous page).
* • Red, Green/sync and Blue, for RGB with sync on Green
(3-cable hookup)
• Red, Green, Blue and H/HV, for RGB with Composite sync
signals. (4-cable hookup)
• Red, Green, Blue, H/HV and V, for RGB with separate
Horizontal and Vertical sync signals. (5-cable hookup)
Front Panel DIP Switch Settings
Set the six DIP switch settings of the SS 200:
Switch 1: On = 75-Ohm input termination
Off = 510-Ohm input termination
Switch 2: On = Disable Horizontal shifting
Off = Enable Horizontal shifting
Switch 3: On = Disable (remove) Serration pulses
Off = Enable (pass) Serration pulses
Switch 4: On = Enable Vertical correction
Off = Disable Vertical correction
Switch 5: On = Separate H & V Sync on output
Off = Composite Sync on output
Switch 6: On = Negative (-) Sync Polarity on output
Off = Sync follows input
Operation
1. Power On the computer and monitor.
2. Power On the output device.
3. If necessary, adjust the Horizontal shift control knob on the front
panel of the SS 200.
Extron • SS 200 Sync Processor • User’s Guide 2
Installation and Operation
75/510 H-SHIFT SERR V. CORR HV OUT NEG
Extron • SS 200 Sync Processor • User’s Guide 3
Installation and Operation
1.250
2.870
6.300
3.150
5.740
0.6
0.173
1.25" X 5.74" OPENING ON DESK
= Bracket hole diameter - 4 places
Thru Desk
Under
Desk
Recommended pilot drill hole size for supplied screws = 3/32” x 1/4” deep.
Thru desk mounting template
(Requires mounting kit P/N 70-077-02)
All dimensions are in inches
SS 200
75/510 H-SHIFT SERR V. CORR HV OUT NEG
SS 200
75/510 H-SHIFT SERR V. CORR HV OUT NEG