NXG Technology NX-W6.2-X - Manual (Page 2)

Warranty Service
Warranty service must be performed by an authorized service
center, usually a NXG speaker systems dealer or its authorized
agent. You may obtain a list of authorized service centers by con-
tacting NXG. All warranty repairs must be accompanied by the orig-
inal bill of sales. No other document is acceptable or is required.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
NXG reserves the right to revise speaker system specifications
without notice.
(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within three years
from the date of the original customer’s purchase, we will, at our option, repair or replace the
defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular purpose,
are limited in duration to the length of this warranty.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at our
option. NXG shall not be liable for incidental or consequential damages of any kind or character
because of product defects. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply.
5. Attach the wire to the input terminals on the rear
of the speaker. Remember to maintain proper polarity
with the amplifier by attaching the positive (+) lead to
the red terminal and the negative (-) lead to the black
terminal.
6. See Fig. 5. With the speaker wire attached to the
speaker, slide the speaker up inside the cut-out hole.
Center the speaker in the cut-out hole and turn the
six locking screws clockwise until the speaker is
drawn up snugly to the wall board from behind,
clamping the speaker in place. Try to tighten each
screw equally. Replace the speaker grill by gently
pressing it into place.
New Construction
1. Determine speaker locations and mark them on
your plans for future reference.
2. If possible, run speaker wires after HVAC and
electrical wiring is in place.
3. Secure speaker wires in place along the run
with insulated staples only and be careful not to
pierce the wire’s insulation. Allow a bit of slack for
expansion of building materials.
4. Needless to say, the actual speakers should not
be installed until the wall board is in place. In the
meantime, leave several feet of wire coiled up and
secured at the back side of the mounting hole.
5. To complete the installation follow steps 2
through 5 above.
Operational Check
After making all connections it’s a good idea to make
sure every thing is working properly. Turn on your
surround or stereo system making sure the volume
control is turned down and that the balance control is
in the center position. Activate a musical or movie
source such as FM, a CD or DVD player. Gently turn
up the volume, you should hear sound coming from
your new NXG speakers. If no sound is heard from
any or all speakers, switch off the system immediately
and check for open or loose connections, wrong polar-
ity or shorts, or proper source selection.
FIG. 5
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)
FIG. 4
NX-W6.2-X Specifications
Maximum Power Handling: 5 - 150 watts
Sensitivity: 90dB @ 1 watt/1 meter
Frequency Response: 50 Hz-22,000 Hz
Driver Complement:
6 1 /
2
˝ (165mm) compression-molded mineral-filled polymer cone woofer with rubber surround
1˝ (25mm) pivoting liquid-cooled soft dome tweeter
Nominal Impedance: 8 ohms
Overall Dimensions: 12 1 /
8
˝ H x 8 3 /
4
˝ W x 3 1 /
2
˝ D (308 mm x 222 mm x 89 mm)
Required Wall Cutout: 10 7 /
8
˝ H x 7 3 /
8
˝ W (276 mm x 187 mm)