Alpha Technologies Te25xh - Manual (Page 30)

INSTALLATION INSTRUCTIONS:
STEP 1: UNDO EXISTING HARDWARE (ITEMS 6, 10 AND 14) ON THE BACK OF
ENCLOSURE. INSTALL HOOK BRACKET (ITEM 2) AS SHOWN RE-USING
REMOVED HARDWARE, OR THOSE SUPLLIED IN KIT.
STEP 2: DRILL PROPERLY SIZED HOLES IN POLE TO INSERT RODS (ITEM 8)
THROUGH AS SHOWN. PLEASE NOTE THAT POLE MOUNTING HARDWARE
IS PROVIDED BY CUSTOMER.
STEP 3: ADJUST RODS TO ACCOMMODATE BRACKET AND HARDWARE. PRE-INSTALL
WASHER AND NUT (ITEM 12 & 13) ON REAR OF RODS. INSTALL POLE
MOUNT BRACKET (ITEM 1) ONTO POLE WITH RODS AS SHOWN.
STEP 4: INSTALL WASHER AND NUT (ITEMS 12 & 13) ON FRONT OF RODS.
TORQUE FRONT NUT TO 96 ft-lb WHILE HOLDING NUT ON REAR
WITH A WRENCH. LOCK FRONT AND REAR NUTS IN PLACE WITH
A SECOND NUT TORQUED TO 96 ft-lb. BE SURE TO HOLD FIRST NUT
IN PLACE WITH A WRENCH WHILE TORQUING SECOND NUT. APPLY A
DROP OF RED PAINT ON THE END OF NUT NEAR THREADS TO INDICATE
IT HAS BEEN PROPERLY TORQUED.
STEP 5: ENSURE THAT REAR BRACKET HOOKS INTO SLOT ON POLE MOUNT
BRACKET WHEN LOWERING ENCLOSURE ONTO PLATFORM. PLEASE NOTE
THAT 6 EXISTING SCREWS AND WASHERS ON BOTTOM OF ENCLOSURE NEED
TO BE REMOVED PRIOR TO INSTALLATION AS SHOWN. USE NEW HARDWARE
(ITEMS 7, 9 AND 11) PROVIDED TO ATTACH ENCLOSURE TO BASE OF
PLATFORM.
STEP 6: ATTACH SECURITY HARDWARE (ITEMS 21, 22, 23 AND 24) PROVIDED USING
HOLE IN REAR BRACKET IF REQUIRED.
2
STEP 5 & 6
9 11
6 PLACES
7
SEE INSTALLATION
INSTRUCTIONS
STEP 6
N.T.S.
SIZE DWG NO. TYPE
B
SHEET
T I T L E
ISSUE
DATE OF
TOLERANCES
SCALE
APPROVED
CHECKED
DRAWN
DESIGN MATERIAL
FINISH
FOR MANUFACTURING WITHOUT ITS WRITTEN CONSENT.
ARGUS TECHNOLOGIES AND SHALL NOT BE COPIED OR USED
THESE DESIGNS AND SPECIFICATIONS ARE THE PROPERTY OF
REV
O
2007/07 ME
c 2007 ARGUS TECHNOLOGIES
2007/07 VED
D2 C
0.01"
0 . 0 4 "
X.XXX
0 . 0 2 "
X.X
X.XX
0 . 2 5 m m
037-176-04
GENERIC, Te25xh
KIT, PLATFORM, POLE MOUNT
037-176-20
SEE B.O.M.
Doc. 070-024-83
2 2
VED
VED
2007/07
2007/07
D2 C
VED 2007/07
ME 2007/07
N.T.S.
SIZE DWG NO. TYPE
B
SHEET
T I T L E
ISSUE
DATE OF
TOLERANCES
SCALE
APPROVED
CHECKED
DRAWN
DESIGN MATERIAL
FINISH
FOR MANUFACTURING WITHOUT ITS WRITTEN CONSENT.
ARGUS TECHNOLOGIES AND SHALL NOT BE COPIED OR USED
THESE DESIGNS AND SPECIFICATIONS ARE THE PROPERTY OF
REVISIONS
LTR DESCRIPTION APPD DATE
REV
1mm
PER P.O. and
[X.XX]
0 . 5 m m
[X]
[X.X]
0.01"
0 . 0 4 "
X.XXX
0 . 0 2 "
X.X
X.XX
0 . 2 5 m m
037-176-04
GENERIC, Te25xh
KIT, PLATFORM, POLE MOUNT
037-176-20
SEE B.O.M.
Doc. 070-024-83
2 2
VED
VED
2007/07
2007/07
[X] 1mm
[X.X] 0 . 5 m m
[X.XX]
PER P.O. and
REV BY
FINAL ASSEMBLY - FRONT BOTTOM VIEW