Astro Pneumatic 4550 Air Operated Paint Shaker - Manual

4550
AIR OPERATED PAINT SHAKER
AIR OPERATED PAINT SHAKER
Important
When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
Unpacking
www.astrotools.com
1
1
1
1
3
1
1
1
1
1
1
1
1
1
2 4550-A01
4550-A02
4550-A03
4550-A04
4550-A05
4550-A06
4550-A07
4550-A08
4550-A09
4550-A10
4550-A11
4550-A12
4550-A13
4550-A14
4550-A15 Safety Valve
Oil Gage
Pipe Joint
Safety Guard
Collar
Cap Nut
Plate
Oil Collar
Oil Collar
Screw Shaft
Driven Shaft
Spring Washer
Nut (1/2
" - 12)
Retaining Ring
Oil Cup
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1 3
2
2
1
5
1
1
1
2
1
1
1
1
2
1 1
4
4
1
1
1
1
1
1
1
2
3
6 4550-A16
4550-A17
4550-A18
4550-A19
4550-A20
4550-A21
4550-A22
4550-A23
4550-A24
4550-A25
4550-A26
4550-A27
4550-A28
4550-A29
4550-A30 Washer
Shaft
Bearing
Cylinder Drive Shaft
Cylinder
Oil Seal
Oil Collar
Piston
O-Ring (40.64 x 5.34)
Piston Washer
Screw Bolt
Cylinder Washer
Valve Casing
O-Ring (40.8 x 1.85)
Valve Seat
4550-A31
4550-A32
4550-A33
4550-A34
4550-A35
4550-A36
4550-A37
4550-A38
4550-A39
4550-A40
4550-A41
4550-A42
4550-A43
4550-A44
4550-A45 Screw Bolt
Washer
Vibration Washer
Nut (3/8 " - 16)
Screw Bolt
Valve Washer
Pipe Clip
Pipe
Screw Bolt
Pipe Joint (90 )
Screw Bolt
Washer
U-Bolt
Nut (3/8
" - 16)
Screw Base
4550-A46
4550-A47
4550-A48
4550-A49
4550-A50
4550-A51
4550-A52
4550-A53
4550-A54
4550-A55
4550-A56
4550-A57
4550-A58 Screw Base
Screw Bolt
Nut (M10)
Screw Hand
Screw Base
Washer
Support Base
Hand Wheel
Spring Pin
Oil-Paint Base
Screw Bolt
Washer
Spring Pin
54
55
53
42 17
16
28
19
37
36
39
40
38
30
31
32
33
35
34
21
27
20
22
41
26
25
23
18
1
2
3
5 7
11
9
10
4
13
12
14 47 46
45
15
48
44
50
52
43
49
8
32
24
33
39
15
29
6
57 58
35
51
56
Call 1.800.221.9705 for questions concerning performance of the product
or other inquiries.
4550
372 Old US Highway 52 South
Mount Airy, NC 27030
AIR OPERATED PAINT SHAKER
3
Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year from the date of 1st use. Astro
reserves the right to determine whether the product failed because of defective
material, workmanship or other causes and to charge back for missing parts. Astro
Pneumatic Tool Co., at its discretion, will repair products covered under this warranty
free of charge. The original user is to return the product (with the exceptions listed
below) with the distributor’s name, address, adequate proof of date of purchase or a
copy of warranty card, and a short note explaining the problem. Failures caused by
accident, alteration, or misuse are not covered by this warranty.
Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and
may not be transferred to subsequent owners.
This warranty is in lieu of all other warranties, expressed or implied, including
warranties of merchantability and fitness for a particular purpose. Some states do not
allow the exclusion of limitations of incidental or consequential damages so the above
limitations may not apply to you. All claims must be sent to:
Astro Pneumatic Tool Company
P.O. Box 251935
Los Angeles, CA 90025
PLEASE DO NOT RETURN ANY PRODUCT TO THE P.O. BOX.
CALL 1-800-221-9705 FOR INSTRUCTIONS.
SPECIFICATIONS:
• Capacity:
• Air Consumption:
• Air Inlet:
• Speed:
• Operating Pressure Ranges:
• Shaking Time:
• Shaking Distance: 8.45Pint (1.06 Gallon)
1.35 CFM
1/4" NPT
1400 Cycles/Min.
90 to 120 PSI at Inlet
1.5 Min.
85~90mm
Product Information
• Heavy duty construction
• Compact design
• Rubber coated clamps will accommodate
Pints Quarts and Gallons
• Quieter and faster operation
• Includes oiler
4550
AIR OPERATED PAINT SHAKER
MAINTENANCE INSTRUCTION:
1.) LUBRICATION:
Oil paint shaker with 2 - 3 drops of air tool oil once every 3 weeks if there
is no moisture in air line or air supply. If moisture in air line or air
supply exists, use 2 - 3 drops or air tool oil, daily. DO NOT OVER OIL.
2.) TIGHTNESS OF PARTS:
Regularly check whether all connection parts are fastened securely.
Follow this procedure daily before beginning work.
3.)
STORAGE:
Avoid storing the tool in a location subject to high humidity. If the tool is
left unused, the residual moisture inside the tool can cause rust. Before
storing and after operation, oil the tool at the air inlet with spindle oil and
run it for a short period.
4.) DISPOSAL:
Follow national legislation of waste disposal. Never drop into fire.
5.) ORDERING SERVICE PART:
For further operational and handling information or for replacement of
parts and components, contact the sales agent from where you purchased
the tool, or the service division of our company. *When ordering parts and
components, give each part number, name and quantities.
OPERATION INSTRUCTION:
1.) Before operating shaker, clamp can securely and
use caution not to crush can.
2.) To start shaker: Open On/Off control valve.
3.)
IMPORTANT: NOT FOR USE WITH AEROSOL CANS
4.) Recommended air pressure 90 to 120 psi at inlet
1) The tool shall not be used in potentially explosive atmospheres.
2) Disconnect the air hose before changing or adjusting any inserted tools.
3) Before using tool, please confirm all couplings and plugs are
fixed securely. Air hose that is under pressure may lash out when
disconnected and could lead to serious injuries.
4) Prevent loose clothes, long hair or any other personal accessories from
coming close to moving parts to reduce the risk of being injured.
5) Excessive high air pressure, that exceeds the maximum pressure,
may cause injuries to user.
6) Exposure to strong vibration for extended time may cause harm to operator.
7) Slip/Trip/Fall is a major reason of serious injury or death.
Beware of excess hose left on the walking or work surface.
9) Wearing correct breathing protection will help avoid inhaling dust or
handling debris from work process that can be harmful to your health.
10) High sound level can cause permanent hearing loss.
Use hearing protection while operating tool.
11) Be aware of work surface dangers prior to beginning work.
It is recommended that shaker is installed a minimum of 2’-3’ from
other objects that could lead to damage or injury if shaker comes in contact.
12) This power tool is not insulated. If contact is made with an
electric current, injury may occur.
13) Dust created by sanding, sawing, grinding, drilling and other related activities
may expose the user to dust and/or microscopic particles that may contain
chemicals known to the State of California to cause cancer, birth defects or
other reproductive harm.
14) Not for use with aerosol cans.
Users of this tool should review the chemical composition of the work
surface and any products used in conjunction with the operation of this tool
for any such chemicals prior to engaging in any activity that creates dust
and/or microscopic particles.
Users should obtain the Material Safety Data Sheets for all identified
chemicals, either from the manufacturer or their employer, and proceed to
study, understand, and follow all instructions and warnings for exposure
to such chemicals.
Some examples of these chemical are: lead from lead based paints;
crystalline silica from bricks, cement and other masonry products;
and arsenic and chromium from chemically treated lumber.
A listing of the chemicals can be obtained at www.oehha.ca.gov
under Proposition 65.
In order to reduce their exposure to such chemicals users should always:
- work in well-ventilated areas .
- wear appropriate safety equipment and clothes that are specifically
designed to filter out microscopic particles
SUGGESTED AIR LINE CONNECTION
Also Available:
#4551Paint Shaker Stand
Product: 4550 Manual
Dimension: 8.5"x 11"/page
Date: 2007/10/2
Color:
outside
inside
Black