Atec EMCO-5407 User Manual
Gtem, Rf emissions/immunity test cell, Features
1
11
11
GTEM!
Models 5405/5407
RF Emissions/Immunity Test Cell
Features:
l
New Sizes, Lower Price
l
25x25x25 cm
3
or 40x40x40 cm
3
EUT Test Volumes
l
For All Phases of EMC Testing:
- Design Qualification
- Pre-Compliance
- Full Compliance
- Post Production
l
For Full Compliance Demonstration of:
- IEC 61000-4-3, EN 61000-4-3,
-
MIL-STD 462, ANSI C63.4,
-
EN 55022 and VDE 0871
l
Reduces Test Time
-
≈≈≈≈≈
8:1 for RE (vs. OATS)
-
≈≈≈≈≈
2:1 for RI (vs. chamber)
EMCO’s Model 5405 and 5407 GTEM!
TM
Cells enable users to perform radiated
emissions and radiated immunity tests
in less time than at either an OATS or in a
chamber. Tests can be performed quickly
and accurately throughout the product
life cycle. Beginning with design
qualification testing and moving through
to pre-compliance testing, full compli-
ance testing and production sampling,
EMCO’s GTEM! cells are time-saving
devices for your test lab. A typical
radiated emissions test (10,000 point
scan) can be completed in 15 minutes or
less, while a typical radiated immunity
test can usually be completed in half the
normal time.
The GTEM! is based on experience, not
experimentation. Originally developed in
the EMC Baden (Switzerland) labs of
ABB, the cell has been accepted in the
EMC community for more than 10 years,
and is field proven daily at more than
400 installations worldwide. Measure-
ments made with a GTEM! are accepted
for final compliance demonstration by
the FCC for Part 15 & 18 radiated
emissions testing, and comply with IEC
61000-4-3 Annex D for immunity testing.
The GTEM!’s unique tapered shape,
offset septum, resistive termination
network and absorber-lined backwall
remove performance limitations of TEM
cells and boxy enclosures. Electromag-
netic wave and RF current termination
are smooth and controlled. Field
uniformity is ± 3 dB up to 1 GHz, and
± 4 dB above 1 GHz.
These new models are the result of an
on-going program of research and
development. The new sizes are a result
of customer requirements, while the
lower price is a result of process and
material improvements.
Standard Configuration
l
GTEM! cell with door placement on
right side (viewed from feed)
l
Mobile base with locking caster wheels
l
Hydraulically damped door with
recessed contact mechanism, contact
RF sealing and shielded window
l
Rantec high performance RF anechoic
absorber
l
Single phase, 20A, 50/60 Hz filter with
choice of two floor mounted receptacles
l
One wall mounted fiber optic
feedthrough (4 lines)
l
Three N connector feedthroughs
New Model 5405
TM
For a performance comparison of the
GTEM!
TM
and several contemporary TEM
devices, request a reprint of a paper by Dr. H.
Garbe, University of Hannover, Field
Homogeneity in Different TEM Waveguides.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
Information presented is subject to change as product enhancements are made. Contact ETS Sales Department for current specifications.
2/00 - 1k S © 2000 ETS-EMCO REV-A
2/00 - 1k S © 2000 ETS-EMCO REV-A
2/00 - 1k S © 2000 ETS-EMCO REV-A
2/00 - 1k S © 2000 ETS-EMCO REV-A
2/00 - 1k S © 2000 ETS-EMCO REV-A
USA:
Tel +1.512.835.4684
Fax +1.512.835.4729
FINLAND:
Tel +358.2.8383.300
Fax +358.2.8651.233
ONLINE:
[email protected]
http://www.emctest.com