Atec Agilent-8560EC-65EC Series - Manual (Page 7)

Amplitude Specifications, continued
Frequency response
in dB, 10 dB input attenuation, dc coupled
relative / typical relative / absolute 2 / typical absolute 3
8560EC 8561EC 8562EC 8563EC 8564EC, 8565EC
100 MHz to 2 GHz 0.7/0.7/–/– 0.9/0.8/–/– 1.0/0.8/–/– 0.9/0.8/–/–
30 Hz 1 to 2.9 GHz 1/0.8/1.5/1.0 1.0/0.7/1.75/1.0 1.25/0.8/1.8/1.0 1.25/0.8/1.8/1.0 1.0/0.8/1.5/1.0
2.9 GHz to 6.46.GHz 1.5/1.1/2.5/1.5 1.5/1.1/2.5/1.5 1.5/1.0/2.4/1.5 1.7/1.4/2.6/1.8
6.46 to 13.2 GHz 2.2/1.5/2.9/2.0 2.2/1.5/2.9/2.0 2.6/2.2/3.0/2.8
13.2 to 22 GHz 2.5/1.5/4.0/2.5 2.5/2.5/4.0/3.5
22 to 26.8 GHz 3.3/2.2/4.0/2.5 3.3/2.2/4.5/4.0
26.8 to 31.15 GHz 3.1/2.9/4.0/3.0
31.15 GHz to 40 GHz (Agilent 8564EC) 2.6/2.4/4.0/3.2
31.15 GHz to 50 GHz (Agilent 8565EC) 3.2/3.0/4.0/4.0
Band switching uncertainty
±1 dB (added to relative frequency response for between-band measurements)
Calibrator output
300 MHz x (1 ± frequency reference accuracy 4 ) at –10 dBm ±0.3 dB
Input attenuator
Switching uncertainty (referenced to 10 dB attenuation)
30 Hz to 2.9 GHz for 20 to 70 dB settings of input attenuator:
±0.6 dB/10 dB step, 1.8 dB maximum
Repeatability ±0.1 dB (nominal)
IF gain uncertainty
±1 dB (0 to –80 dBm reference levels with 10 dB input attenuation)
IF alignment uncertainty
±0.5 dB (additional uncertainty only when using 300 Hz RBW)
Resolution bandwidth switching uncertainty
±0.5 dB (relative to 300 kHz RBW)
Pulse digitization uncertainty
(pulse response mode, PRF > 720/sweep time)
Log Linear
RBW ≤ 1 MHz < 1.25 dB pk-pk < 4% of ref level
RBW = 2 MHz < 3 dB pk-pk < 12% of ref level
Standard Deviation (RBW < 1 MHz) < 0.2 dB (nominal)
Time-gated spectrum analysis
Gate delay 5 Edge mode Level mode
Range 3 µs to 65.535 ms ≤ 0.5 µs
Resolution 1 µs
Accuracy ±1 µs
(From GATE TRIGGER INPUT to positive edge of GATE OUTPUT)
Gate length
Range 1 µs to 65.535 ms
Resolution 1 µs
Accuracy ±1 µs
(From positive edge to negative edge of GATE OUTPUT)
7
1. Operation below 9 kHz requires Option 856xEC-006
2. Absolute flatness values referenced to 300 MHz CAL OUT
3. Typical values at 25 °C
4. Frequency reference accuracy = aging x time since last adjustment + initial achievable accuracy + temperature stability
5. Up to 1 µs jitter due to 1 µs resolution of gate delay clock