Atec JDSU-MTS-5800 - Manual

NETWORK AND SERVICE ENABLEMENT
Benefits
• All-in-one handheld tool simplifies multitechnology testing
• Optimized for easy field use with multi-touch screen, scripted workflows, and support
for emerging network technologies
• Guarantees maximum efficiency and success in evolving carrier Ethernet and mobile
backhaul networks
• TrueSAM™ and advanced IP test tools follow best practices with repeatable methods
and procedures for faster service activation and troubleshooting tests with easy-to-
understand results
The T-BERD/MTS-5800 Handheld Network Tester addresses the challenges
of carrier Ethernet evolution. It supports both legacy and emerging
technologies required to handle various network applications including
metro/core, mobile backhaul, and business services installations.
The industry’s smallest handheld instrument can test throughout the
service life cycle, including fiber characterization, service activation,
troubleshooting, and maintenance. Advanced Ethernet test functionality,
such as J-Profiler, wirespeed capture/decode, and automated J-Mentor,
guides field technicians through troubleshooting without using a separate
analyzer instrument.
The T-BERD/MTS-5800 ensures successful mobile backhaul transitions by
validating both Ethernet backhaul synchronization (1588v2 and SyncE)
and front haul (CPRI/OBSAI) BER and delay to guarantee successful mobile
handoff between cell sites, thereby avoiding service degradation.
Applications
• Tests and troubleshoots converged Ethernet/IP networks
at 10 Mbps to 10 G interfaces
– Tests Layer 1-3 Ethernet/IP SLAs with an automated,
enhanced RFC 2544/SAMComplete per ITU-T Y.1564
– Integrated burst testing approach including CBS
verifies buffer settings and TrueSpeed per RFC 6349
for performance testing so you can experience your
network the way your customers do
– Robust network discovery, top talker analysis,
deep packet capture, packet analysis, and expert
troubleshooting guidance capabilities
• Tests TDM/PDH to SONET/SDH at OC-3/STM-1 to OC-192/
STM-64, including service disruption measurements and
path overhead (POH) capture with triggers
• Enables installation and maintenance of OTN networks
up to 11.1 Gbps interface with ODU-0 and Flex support
for Ethernet/IP client interfaces
• Supports 8 G FC dual-port interfaces (along with
1/2/4/10 Gbps) for installation and maintenance of SANs
and low-latency circuits
• Verifies network synchronization
– Emulates a 1588v2 master clock/slave recovery for
proper point-to-point (PTP) message propagation and
packet-delay variation (PDV) verification
– Verifies SyncE frequency synchronization accuracy and
Ethernet synchronization message channel (ESMC)
message propagation
– Measures wander on SyncE, 1PPS, T1, E1, and
2 and 10 MHz signals
• Tests remote radio head (RRH) health with CPRI and
OBSAI FTTA tests
• Supports SFP+ pluggable optics
• Two simple T-BERD/MTS-5800 configurations:
– Single- and dual-port versions
– Fully loaded TDM/PDH to dual 10 G Ethernet, SONET,
SDH, Fibre Channel, and OTN support
Cover page
Figure 1. Carrier Ethernet network
VoD
server
Video
hub office
GIG
OTN
UNI
“demarcation point”
Core network
IP/MPLS, ATM, SONET
Business location B
CE
UNI
“demarcation point”
Business location A
CE
Video
headend
Splitter OLT TB/MTS-5800v2
SoHo
Fiber Characterization
(OTDR, OSA)
SONET/SDH and
OTN Network and Testing
Carrier Ethernet and
Backhaul Testing
Fibre Channel
Network and Testing
CPRI/OBSAI Verification
for FTTA Installations
Mobile
3G/4G
Storage
SAN
switches
Fibre Channel
SAN
TB/MTS-5800v2
TB/MTS-5800v2
TB/MTS-5800v2
TB/MTS-5800v2
TB/MTS-5800v2
T-BERD®/MTS-5800
Handheld Network Test Product Family