Atec Quadtech-1000 Series - Manual

Guardian 1000 Series
Hipot Testers
USES:
• Production Testing of Appliances,
Instruments and Information
Technology Equipment in Accordance
with UL,IEC,TÜV and Other
Standards such as EN60335, EN60950,
EN61010, CSA C22.2 No. 1010.1,
UL3111 and UL1950
• Transformer Electrical Safety Testing
• Electric Motor Safety Testing
• Testing a Variety of Electronic
Components
FEATURES:
• Real and Total Current; 30mA AC,
10mA DC
• Programmable Output Voltage to 5kV
AC and 6kV DC
• Resistance Measurements from
0.1MΩ to 50GΩ
• Programmable Ramp, Test & Fall
Times
• Programmable High & Low Limits
• Open/Short Circuit Check
• Ground Continuity Check with
1ohm Limit
• Arc Detection with Programmable
Limit
• Quick Discharge of DUT in IR and
DC Hipot
• Storage of 99 Tests Setups with
Multiple Steps per Measurement
• Front Panel Lockout
• Remote I/O & RS232 Interfaces, Std.
• IEEE-488 or Printer Interfaces, Opt.
• 8 Channel Scanner (1030S)
Introduction
A complete dielectric testing solution, with three models from which to choose. The
Guardian 1010 for AC Hipot testing, the Guardian 1030 for AC/DC Hipot testing and
insulation resistance (IR) measurements; and the Guardian 1030S which combines
both AC and DC Hipot tests and IR measurements with eight HV scan channels. All
models have Open/Short Circuit detection and Load/Line regulation to ensure proper
device connection and measurement integrity. The digital display and user friendly
controls allow test parameters and limits to be set without the high voltage activated.
Description
The Guardian 1010 AC Hipot Tester performs AC dielectric withstand tests. The test
voltage can be programmed in the range from 50VAC to 5kVAC with a resolution of
1V. The maximum total output current is 30mA.
The Guardian 1030 AC/DC/IR Hipot Tester has all the features of the Guardian
1010 with the addition of DC hipot and IR measurement capabilities. The test voltage
can be programmed in the range from 50VDC to 6kVDC with a resolution of 1V. The
maximum total current is 10mA. The IR measurement range is from 0.1MΩ to 50GΩ
with test voltages from 50 to 1000VDC.
The Guardian 1030S AC/DC/IR/SC Hipot Tester has all of the features of the
Guardian1030 plus eight HV Scan Channels for multi-point testing.
Real and Total Current Measurement: Accurately measure the leakage current of
highly capacitive devices by separating the real and reactive current.
Ground Fault Interrupt (GFI): Provides an extra level of safety for the operator and
equipment. The instrument shuts down when the current balance exceeds 0.5mA.
G1000 Series units also have an interlock for use with palm switches, light curtains,
hoods and other safety switches.
Quick DUT Discharge: In both the DC hipot and IR tests the device under test is dis-
charged back through the HV transformef for a rapid and safe discharge.
Ground Continuity Check: All of the Guardian 1000 Series units have a ground con-
tinuity check feature to determine that the resistance, between the ground blade of the
power cord and any exposed metal on the product, is less than 1 ohm.
Open/Short Circuit Mode: All Guardian 1000 Series models have OS mode to detect
connection of the device in order to prevent false readings. Open ensures the device
under test is connected properly and Short ensures the device is not shorted prior to
applying the high voltage. The Open value is programmable from 10-100% and the
Short value from 100-500%.
Multi-Purpose AC/DC/IR/SC Hipot Testers
G1030S: EMC only
For more detailed information on
specifications, pricing and special
purchase, rent and lease options,
contact us at:
www.quadtech.com
800-253-1230
Hipot Testers • LCR Meters • Cable Testers • AC/DC Programmable Power Sources
• Megohmmeters • Milliohmmeters