atwood Truck Camper Remote With Accessory Controlling Ability - Manual (Page 4)

4
tROublEshOOtIng
If all or any of the jacks or landing legs fail to operate:
1. Check whether the 12VDC battery is fully charged. You may need to recharge it.
2. Check that the camper jack cords are securely plugged into the exterior
sockets. You may need to pull a plug out and replug it.
3. If the motor will not extend/retract the jack and the motor is making a
ratcheting sound (clutch slipping), do not use the manual override. Immediately
contact an Atwood Service Center and have jack replaced. Do not use the jack
until replaced.
4. Assure the activation switch is turned on. The LED on the switch pad should be lit.
5. Check that you are within 20 feet of the camper.
6. Replace the 9V battery or plug the audio cable (R) into the side of the remote
(P) and the opposite end into the front of the activation switch (Q).
7. Check that the battery terminals are clean and have no corrosion.
8. Look to see if other radio frequency devices such as an automobile key fob,
cellular phone, TV remote control, are operating within range of your remote.
These devices will make the jacks pause. Lift your finger from the button on the
remote and re-press the button. Also the audio cable can carry the signal, plug
the audio cable (R) into the side of the remote (P) and the opposite end into
the front of the activation switch.
If the jacks keep running, hold down the power-select on the remote until the LED
turns off. This will shut the power off to the jacks. If not, unplug the jack(s) from
its (their) exterior socket(s).
REMOtE aCtIVatIOn sWItCh
• Red ACTIVE LED
• SOLID - system is active and ready for operation
• OFF - system is in sleep mode
• Fast continuous blinking - system is in LEARN TRANSMITTER mode
• 1x blink with pause - low voltage detected - no operation allowed
• 2x blink with pause - no transmitter is associated with the base unit
(shipment mode). A transmitter must be associated with the base
unit before operation is allowed. See installation section.
• Blue RF LED
• SOLID - indicates presence of clean RF signal from associated
transmitter
• Blinking - indicates RF interference from another transmitter (more
than 1 transmitter is operating nearby)
• OFF - no RF signal detected
MaIntEnanCE
1. To clean the remote, wipe with a soft cloth dampened with water. Don’t use
cleaners or solvents on the remote, they can harm the body and leak inside,
causing permanent damage. Battery contacts may be wiped with a dry, lint-free
cloth.
2. If the remote gets wet, remove batteries immediately. Dry battery compartment
with a soft cloth to minimize potential water damage. Leave cover off the battery
compartment overnight or until completely dry. Do not use the remote until
completely dry.
3. If power relay module gets wet, turn off circuit breaker to the unit. Allow unit to
fully dry before attempting to use it.
4. If it is not possible to get jack to operate freely, replace jack.
5. Should problems or questions arise, contact your dealer, the camper manufacturer,
or the Atwood Service Department (866) 869-3118.
6. The ball screw jacks and remote controls have a two year warranty as written in
this manual. For more warranty information contact Atwood before having any work
done.
atWOOd lIMItEd WaRRanty
Atwood Mobile Products warrants to the retail owner and subject to the
below mentioned conditions, that this product will be free of defects in
material or workmanship for a period of two years from the original date
of purchase. Atwood’s liability hereunder is limited to the replacement of
the product, repair of the product, or replacement of the product with a
reconditioned product at the discretion of the manufacturer. This warranty
is void if the product has been damaged by accident, unreasonable use,
neglect, tampering or other causes not arising from defects in material or
workmanship. This warranty extends to the original owner of the product
only and is subject to the following conditions:
1. For two (2) years commencing with the date of purchase, Atwood
will provide the replacement or repair of any Hardware System and
Components that are found to be defective by Atwood in material or
workmanship.
2. in the event of a warranty claim, the original owner must contact the
atwood consumer service department, 1120 north main, elkhart,
in 46514 usa. phone: (866-869-3118). Warranty Claim Service
must be performed as approved by the Atwood Consumer Service
Department. Warranty replacement hardware systems and components
or parts will be furnished freight prepaid labor cost to repair or replace
will be limited to the amount of the original purchase price of the systems
and components. The replaced warranty products or parts become
the property of Atwood Mobile Products and must be returned to the
Atwood Consumer Service Department freight prepaid, unless prior
arrangements have been made.
3. This limited warrant is valid only when the product is applied, installed,
maintained and operated in accordance with this Atwood Installation
Maintenance and Operating Manual. Any deviation from these
recommended specifications must be approved in writing by Atwood.
4. ANY IMPLIED WARRANTIES arising by way of State Law, including any
implied warranty of merchantability and any implied warranty of fitness
for a particular purpose are limited in duration to the term of this Limited
Warranty. Atwood makes no further warranty of any nature beyond this
Limited Warranty. No person has authority to enlarge, amend or modify this
Limited Warranty.
5. Any action to enforce this warranty shall not be commenced more than
one (1) year after the expiration of this warranty.