Carlon P&C Flex - Low Res User Manual
Conduit fittings, P&c flex, Installation & fittings
Made in the U.S.A.
P&C Flex
®
Installation & Fittings
www.carlonsales.com
Part Std.
Std. Ctn.
No.
Size
Ctn. Qty.
Wt. (lbs.)
E940H
1
1
/
2
"
25
4
E940J
2"
30
5
E940K-CAR
2
1
/
2
"
4
2
E940L-CAR
3"
5
3
E940M
3
1
/
2
"
20
13
E940N-CAR
4"
5
4
Couplings
Part Std.
Std. Ctn.
No.
Size
Ctn. Qty.
Wt. (lbs.)
P258H
1
1
/
2
"
50
2
P258JT
2"
60
3
P258K
2
1
/
2
"
25
2
P258LT
3"
30
3
P258NT
4"
48
8
Plugs
1. Trenching
Trench should be graded true and free from stones or soft
spots. Backfill should also be free of stones and be firmly
tamped around the sides of the conduit, to develop maximum
supporting strength. Tamping on top of the conduit is not
recommended.
2. Backfill
In rocky soil where it is impossible to have an even trench
bottom, a selected backfill should be put in before laying the
conduit. Selected backfill (not tamped) at least 6" over the
top of the conduit is recommended. After
final backfill is placed, taming may be used
to finish the grade.
3. Duct Placement
Duct may be unreeled directly into trench or
along side trench and subsequently placed
in trench. After placing in trench, secure one
end and stretch it by hand to take up the
slack. Spot backfill to hold in position. Do
not use mechanical stretching equipment.
4. Changes in Direction
Avoid unnecessary turns, dips, or changes in direction. Keep bends as gradual
as possible to assure ease of cable pull-in after duct installation.
5. Pneumatic Rodding
All commonly used vacuum or pressure can be used to rod P&C Flex. The line
carrier (mouse, puck, rocket) should be soft, flexible material designed to fit
snugly into duct without interference.
6. Mechanical Rodding
All commonly used mechanical rodding equipment can be used to rod P&C
Flex. The tip should have a ball-type arrangement to keep rod from catching in
the convolutions on the inside of duct.
P&C Flex
®
Conduit Fittings
Part Std.
Std. Ctn.
No.
Size
Ctn. Qty.
Wt. (lbs.)
E997H-CAR
1
1
/
2
"
10
.9
E997J-CAR
2"
10
1.2
E997K-CAR
2
1
/
2
"
10
1.9
E997L-CAR
3"
10
2.1
E997M
3
1
/
2
"
40
10.2
E997N
4"
30
10.7
Bell Ends
(Schedule 40)
Part Std.
Std. Ctn.
No.
Size
Ctn. Qty.
Wt. (lbs.)
E942H
1
1
/
2
"
25
3
E942J
2"
30
6
E942K-CAR
2
1
/
2
"
4
1.4
E942L-CAR
3"
3
1.5
E942M
3
1
/
2
"
20
12
E942N-CAR
4"
7
5
Female
Adapters
Part Std.
Std. Ctn.
No.
Size
Ctn. Qty.
Wt. (lbs.)
E943H
1
1
/
2
"
25
3
E943J
2"
5
7
E943K-CAR
2
1
/
2
"
5
1.2
E943L-CAR
3"
5
2
E943M
3
1
/
2
"
30
14
E943N-CAR
4"
5
3
Terminal
Adapters
49
P&C Flex
®
Corrugated Flexible Conduit Installation
Techniques
STRETCH DUCT IN ONE DIRECTION
AWAY FROM SECURED END
SPOT BACKFILL
KEEP BENDS AS GRADUAL
AS POSSIBLE
SECURE END
Gross Automation (877) 268-3700 · www.carlonsales.com · [email protected]