Lexibook TSR50 - Manual (Page 4)

4
ENGLISH
Copyright © Lexibook 2006
the list, program your remote control using the quick or auto search function. The
search function tests all the codes one after another and finds the right one for
your device.
Quick search
This search should be used only if Manual search failed or if the brand or correct
model code is missing.
1. Switch on the device to be set to the remote and aim the remote control at the
device.
- If VCR, insert a cassette.
- If SAT, select a program.
- If DVD, insert a DVD.
- If CD, insert a CD.
2. Press the SET key followed by the respective device key on your remote
control. Hold down both keys.
3. When the LED lights up, release the buttons.
4. Press the SET button again. The LED starts flashing and quick code search
starts.
5. In order to trigger the code search you will have to push the POWER key
( ). 5 codes will be transferred. Wait 3 seconds. If nothing happens, press
Power again. Each time the power key is pressed, it will look for 5 new different
codes during 3 seconds. You may need to press the power key up to 100 times
maximum. (approximately 5 minutes).
6. When your device switches off, the correct code has been found. DO NOT
press the POWER button again, as this would restart the code search.
7. Press the respective DEVICE button again to exit the current stage. The LED
stops blinking and remains solid.
8. Return to your device and switch it ON again (by using original remote control
or the device’s front panel buttons).
9. In order to fine tune the search within these 5 codes, you must press the
power key and wait 2 seconds. If nothing happens, repeat by pressing power
again and wait 2 seconds. You should only need to press the power key 5 times
in total before your device turns back OFF.
10. When your device switches OFF, the correct code has been found. DO NOT
press the POWER button again, as this would re-start the code search.
11. Press the respective DEVICE button to store and exit. The LED turns off.
12. During step 8, the SET button can be pressed to return to step 5.
Check whether all applications of your device can be operated using the remote
control keys.
Set-up
There are 3 programming modes: Manual, Quick Search and Automatic
Programming.
Please refer to the code list on page 38 and onwards.
Please always try the manual set-up FIRST, then if no code in the list of brands
and models matches your device, try the Quick Search, and only if this one fails,
try Automatic Programming.
Warning: program one appliance at a time. For example, start by setting your
remote to your TV, then to your DVD player…
Manual setup
Note: it might take up to 10 minutes per device set.
1. Select the device you wish to set (ex.: TV). Search your device’s brand in the
code list attached. There is a different code list for each of the 8 devices which
your remote control can be set to. Mark down the correspondent 3-digit code(s).
One brand may have up to 30 codes. You might have to try several of them
before finding the one relevant to your model (see hereunder). You will have to
repeat the full procedure.
2. Switch on the device to be set to the remote and aim the remote at the device.
- If VCR, insert a cassette.
- If SAT, select a program.
- If DVD, insert a DVD.
- If CD, insert a CD.
3. Press the SET key (
SET
) first and hold it down while pressing the respective
device key on your remote control, hold both keys down. For example:
to program your TV, press first SET and then TV1 simultaneously.
4. When the LED (on upper left corner of the unit) lights up, release the keys.
5. Use the numeric keys to enter the 3-digit code applicable for your device.
6. The LED will turn off; setup is completed.
7. Try some keys on your remote to check if they work properly. If they do, your
settings were successful: you found the right code. You are now ready to set
another device, with the same procedure.
8. If your remote control’s keys do not work, you did not find the right code. Try
the next 3-digit code corresponding to your device’s brand in the list: repeat
steps 3 to 7, until your device responds correctly to the keys pressed on the
remote.
Notes: Press the respective DEVICE button if you wish to stop the manual setup.
If no button is pressed for more than 15 seconds, setup ends automatically and
the LED goes off.
If your device cannot be programmed using manual setup or its code is not in
TSR50IM0116.indd 4 31/03/2006 09:21:39