Tuff Stuff CXT-125 Smith Press System Attachment - Manual (Page 2)

A
bout the Smith Machine Attachment CXT-125
Congratulations on your new purchase of the Smith Machine
Attachment (CXT-100 Option). We hope you are completely
satisfi ed with this product and wish you many years of enjoyment.
T
uff Stuff Equipment
This Tuffstuff product has been built to precise quality standards
and has been carefully packaged to ensure that damage will not
occur during shipment. The Home Lifetime Warranty and signature
indicating fi nal inspection has been conducted by our line foreman,
is an expression of our confi dence in the completeness, the
materials, and workmanship of this product.
W
arranty
SEE A COPY OF WARRANTY ON BACK PAGE.
R
egistration Card
To avoid unnecessary delays in warranty service and to insure that
a permanent record of your purchase is on fi le with our factory,
be sure to complete the warranty registration card and send it to
TuffStuff Fitness Equipment today.
P
rior to the Assembly of the Smith Machine Attachment
1. We advise you to consult your local Tuff Stuff retailer if you should
have a question or problem regarding the proper assembly of
this unit.
T
ool Requirements
1. One 9/16” combination wrench
2. One ratchet
3. One 9/16” socket
4. One rubber mallet
5. Windex or household glass cleaner
6. Measuring tape
7. Utility knife
SC
RE
W
W
ID
TH
W
AS
HE
R
DI
AM
ET
ER
NU
T D
IA
ME
TE
R
SC
RE
W
LE
NG
TH
Hardware Measurement Diagram
S
afety
F
irst
Regardless of how enthusiastic you may be about getting on
your equipment and exercising, take the time to ensure that your
safety is not jeopardized. A moment’s lack of attention can result
in an accident, as can failure to observe certain simple safety
precautions.
1. Read, study and understand the Owner’s Manual and all the
warning labels on this product. Furthermore, it is recommended
to familiarize yourself and others with the proper operation and
workout recommendations for this Tuff Stuff product prior to
use.
2. It is imperative that you retain this Owner’s Manual and be sure
all warning labels are legible and intact. Replacement Owner’s
Manual and labels are available from your local Tuff Stuff
retailer.
3. Consult with your physician before beginning any exercise
program.
4. Use proper discretion when children are present.
5. Keep hands, limbs, loose clothing and long hair well out of the
way of moving parts.
6. Do not attempt to lift more weight than you can control safely.
7. Inspect the Unit for any sign of wear on parts, hardware becoming
loose or cracks on welds. If a problem is found do not use or
allow the machine to be used until the defective part is repaired
or replaced.
Safety Precautions
Note: Due to continuing product improvements, specifi cations and designs are subject to change
without notice.
S
pecifi cations
1. Maximum Wt. Capacity - 250 lbs.
2. Total Machine Weight - 175 lbs.
3. Footprint (LWH) - See Front Cover.
Introduction
Part Three: Lubrication
Bearing and linear bearings systems have advanced over the years but they must be maintained on a regu-
lar basis if you expect them to last and perform effi ciently. TuffStuff uses only the highest quality bearings
and linear motion components that are virtually trouble-free but requires the regular preventive maintenance
to insure long-lasting performance.
1. Bronze and nylon bushings, we recommend on a monthly basis to spray a tefl on-base lubricant
(silicone-free) directly onto the shaft as it passes through these bushings. Spray a small amount
onto the shaft and rotate it through its complete movement and wipe off any excess.
2. Weight stack guide rods and bushings, again use tefl on spray lubricant and this time spray onto
a rag and wipe the guide rods down with this rag on a weekly basis. Do not use WD-40 or other
lubricants as they attract dirt and will crate a mess between the weight plates and bushings.
3. Sealed bearings pivot points, as the name implies are protected from the outside environment
and require no lubrication. During the machine wipe down, wipe the external bearing surfaces
with the damp rag and dried to prevent the build up of dust and sweat.
4. Linear bearing systems are precision, high load components that require regular maintenance.
Dirt and corrosion are the major culprits in linear bearing failure. The hardened shafts must be
wiped down weekly and lubricated with a light layer of tefl on grease. We recommend a tefl on-
base (silicone-free) gel/grease for this purpose. Lack of care and maintenance will result in cor-
rosion of the linear shaft causing the bearings to clogged and jammed
.
If you religiously perform the maintenance procedures, you will increase the life of the machine and ulti-
mately lower your maintenance costs with fewer replaced components and downtime.
Any doubts, equipment with mechanical problems should be placed “Out-of-Service” until all problems are
corrected. If replacement parts are required or maintenance questions, please contact:
TuffStuff Fitness Equipment, Inc.
Service Department
1325 E. Franklin Avenue
Pomona, CA 91766
1-800-961-9377
e-mail: [email protected]
Maintenance
9 CXT-125 Smith Machine Attachment (CXT-100 Option) 2 CXT-125 Smith Machine Attachment (CXT-100 Option)