Step 14 low row cable routing – Tuff Stuff HTX-2000 Dual Stack Functional Trainer v.1 User Manual
Page 26
HTX-2000 Dual Stack-Funtional Trainer
34
17
56
26
Step 14 Low Row Cable Routing
91
37
34
38
59
39
MAKE SURE CABLE RUNS
UNDERNEATH THE SCREW
#74 AS SHOWN ABOVE.
NOTE:
1. SOME PARTS CUT OUT/NOT SHOWN FOR CLARITY.
Congratulations on your new purchase of the Smith-Half Cage
Series. This gym is capable of a variety of different exercises, as-
well-as, smooth and user-friendly adjustment features. In addition,
this gym has been designed to meet the needs and performance
requirements for a suitable home exercise machine. We hope you
are completely satisfi ed with this product and wish you many years
of enjoyment.
This Tuffstuff product has been built to precise quality standards
and has been carefully packaged to ensure that damage will
not occur during shipment. The Home Lifetime Warranty and
signature indicating fi nal inspection has been conducted by our line
foreman, is an expression of our confi dence in the completeness,
the materials, and workmanship of this product.
SEE A COPY OF WARRANTY ON BACK PAGE.
To avoid unnecessary delays in warranty service and to insure that
a permanent record of your purchase is on fi le with our factory, be
sure to complete the warranty registration card and send it to Task
Industries today.
1. We advise you to consult your local Tuff Stuff retailer if you
should have a question or problem regarding the proper
assembly of this unit.
2. Consider the complete surface area of the Smith-Half Cage
Series. Use the overhead view located on the front page for
designing your layout before assembling. Once the Smith-Half
Cage Series has been fully assembled it will be heavy and
diffi cult to move, therefore you should assemble the unit in the
area where it is to be used upon completion.
3. It is recommended that another person assist you with the
assembly of this unit.
4. Neatly organize and identify all parts according to the Parts List
and the Exploded View Diagrams on pages 7 - 9.
1. One 3/4” combination wrench
2. One 9/16” combination wrench
3. One ratchet
4. One 3/4” socket
5. One 9/16” socket
6. One rubber mallet
7. Windex or household glass cleaner
8. One can silicone spray/ tefl on spray lubricant
9. Measuring tape
10. Utility knife
The icons displayed in this Assembly Instructions are used to
facilitate the correct assembly and safe use of this Product, as-
well-as to prevent injury to yourself or anyone else.
provides information necessary to properly
complete a procedure or information which will
make the procedure easier to understand.
indicates a potentially hazardous
situation, which, if not avoided, may result in minor
or moderate injury. It may also be used to alert
against unsafe practices.
provides a instruction to loosely
fasten (
) a hardware assembly
only. This instruction is intended for the alignment
of hardware components during the assembly
process.
provides a instruction to fully fasten
(
) a hardware assembly.
SCREWfiWIDTH
WASHERfi
DIAMETER
NUTfi
DIAMETER
SCREWfiLENGH
T
1. Read and follow each step of this Assembly Instruction Manual
in sequence. Do not skip ahead, as it will result in an improper
assembly or in having to disassemble parts later.
2. During the assembly of this unit you will be instructed to leave
some Hex Head Cap Screws loosely fastened. Naturally, they
will be fully fastened later in the assembly process. This is done
to prevent any diffi culty with alignment of some parts during this
assembly.
Due to continuing product improvements, specifi cations and designs are subject to change
without notice.
TBU-335
THC-43C
TSM-45L
1. Maximum Wt. Capacity
N/A
400 Lbs.
300 Lbs.
2. Total Machine Weight
220 Lbs.
40 Lbs.
80 Lbs.
3. Footprint (LWH)
- See Front Cover
FULLY FASTEN