Accusplit AH190M28 - Manual (Page 4)

24 25
26 27
ADDITIONAL INFORMATION
Replacing the Battery
1. When the figures on the display start to blink, it is time
to replace the battery.
2. The unit uses one Type CR2032 3-volt lithium battery.
3. Insert a coin into the slot at the bottom of the body
case. Twist the coin to remove the front case.
4. Locate the BATTERY HOLDING PLATE at the bottom
left corner of the inside case. Remove the plate by
loosening the two small screws with a small Phillips
head screwdriver.
6. CAUTION: Please DO NOT TOUCH inner pedometer
parts, other than battery. Touching the sensor
mechanism may affect the accuracy of the pedometer.
7. Reinstall the BATTERY HOLDING PLATE by tightening
the two screws. Put the case back together by matching
the top edges of the front case and back case together,
then pressing the bottom of the case together. If the
two halves don’t go together easily, check if the front
case is upside down!
8. Reset the CLOCK, WEIGHT, and STRIDE to restore all
functions to your pedometer.
28 29
30 31
Changing the Unit of Measure
To change between English (feet, pounds) and metric units:
1. Repeatedly press the yellow MODE button until display
is in STEP mode.
2. S1: Press yellow S1 (MODE) button for 2 seconds to
enter SET mode.
3. S2: Press yellow S2 (MODE) button repeatedly until
STRIDE setting flashes (there will be a line under “DIST”).
4. S3: Simultaneously press and hold the yellow S2 (MODE)
and S3 ▲ (MEMORY) buttons for at least 5 seconds. The
unit will shift to the other measurement system.
5. S4: Press and hold yellow S4 (MODE) button for
2 seconds to exit SET mode.
INDEX
Battery, replacing . . . . . . . . . . . . . . . . . .26-28
Clock, setting . . . . . . . . . . . . . . . . . . . . . . . .5-7
Current day’s results, viewing . . . . 2-3, 18-20
Exiting setup mode. . . . . . . . . . . . . . . . . . . 13
Memory . . . . . . . . . . . . . . . . . . . . . . 2-3, 21-23
Memory, resetting . . . . . . . . . . . . . . . . . . . 24
Safety Leash . . . . . . . . . . . . . . . . . . . . . . 16-17
Setting up pedometer. . . . . . . . . . . . . . . .4-13
Speedometer. . . . . . . . . . . . . . . . . . . . . . . . 25
Stride Length, setting . . . . . . . . . . . . . . . 10-13
Unit of measure, changing. . . . . . . . . . . . . 29
Wearing pedometer . . . . . . . . . . . . . . . . . . 14
Weight, setting . . . . . . . . . . . . . . . . . . . . . . . 8
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Resetting the Memories
1. Auto Reset: At 3:50 AM every day, the previous day’s
records are automatically saved and figures in the
main display window are automatically reset to 0. You
do not need to press the RESET button every day.
2. Manual Reset: If you want to reset today’s data to 0,
press and hold the yellow RESET button for 2 seconds.
Note: Resetting today’s steps before automatic nightly rollover
prevents them from being tallied in memory.
3. System Reset: To reset all memories to 0, press the
recessed SYSTEM RESET button in the lower left corner
of the front of the display. (Use a pen or the end of a
paper clip.) Note: In case of irregular display due to static electricity,
pressing the SYSTEM RESET button, and then resetting the CLOCK,
WEIGHT, and STRIDE settings, will return the unit to normal.
Using the Speedometer
The SPEED function answers the question, “How many sec-
onds did I take to walk 10 steps?” (in mph or kph). SPEED is
displayed in the lower right hand corner of the display in all
modes EXCEPT memory recall. Until your speed for the next
10 steps is calculated, the latest speed remains in the display.
NOTE: You must set your STRIDE length for accurate SPEED
measurements.
NOTE: If you took longer than 12 seconds to walk 10 steps,
or you stop walking for longer than 12 seconds or walk “off
and on,” the measurement is cancelled and Walk Speed dis-
play continues to show the walk speed for the last complete
set of 10 steps.
Terminal
Screws
NO-PROOF-OF-PURCHASE LIMITED WARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
See www.accusplit.com/support for details
5. Take out the old battery and replace it with a new
battery. Place the battery’s positive (+) terminal FACE
UP while you install it into the pedometer.