CHIEF SL151 Series - Manual (Page 2)

SL151 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION
alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING
:
FAILURE TO READ AND
FOLLOW THE FOLLOWING INSTRUCTIONS CAN RESULT
IN SERIOUS PERSONAL INJURY, DAMAGE TO EQUIPMENT
OR VOIDING OF FACTORY WARRANTY. It is the installer’s
responsibility to make sure all components are properly
assembled and installed using the instructions provided.
IMPORTANT ! : Model SL151 is suitable for use in Other
Environmental Air Space in Accordance with Section 300.22(C)
of the National Electrical Code.
The SL151 can optionally be attached to an existing 1-1/2" NPT
or NPSM following ANSI/ASME B1.20.1 (Schedule 40, 0.154"
minimum thickness steel or aluminum - ASTM B221) threaded
extension column using a UL Listed SMA-602 pipe adapter
assembly (not included).
When using an electrical mounting system, basic precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS
PRODUCT!!!!
DANGER:
TO REDUCE THE RISK OF
ELECTRIC SHOCK:
1. Always turn off power at source before cleaning.
WARNING:
TO REDUCE THE RISK OF
BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS:
• Always turn off power at source before putting on or
taking off parts.
• Use this mounting system only for its intended use as
described in these instructions. Do NOT use
attachments not recommended by the manufacturer.
• Never operate this mounting system if it has a
damaged test cord or test plug. If it is not working
properly during testing, return the mounting system to
a service center for examination and repair.
• Keep the test power cord away from heated surfaces.
• Never operate the mounting system with the air
openings blocked. Keep the air openings free of lint,
hair, and the like.
• Never drop or insert any object into any opening.
• Do not use near water. Do not expose to dripping or
splashing water. Do not place objects filled with liquids,
such as vases, on this apparatus.
• Do not use outdoors unless marked for outdoor use.
• Route cords and cables as shown in the installation
instructions.
• To disconnect, turn all controls to the off position, then
turn off power at source.
WARNING
:
RISK OF ELECTRIC SHOCK!
Connect this mounting system to a properly grounded outlet
only. See Grounding Instructions.
Connection to the building wiring shall be done according to
National Electrical Codes ANSI/NFPA70 and the Canadian
Electrical Codes, CSA C22.1 and CSA C22.2 and an
appropriate listed disconnect device (e.g. circuit breaker or
fuse) shall be incorporated in the building installation wiring.
CAUTION:
Changes or modifications to this
unit not expressly approved by the manufacturer can void the
units FCC compliance rating and make the unit illegal to
operate.
WARNING
:
Failure to provide adequate
structural strength for this component can result in serious
personal injury or damage to equipment! It is the installer’s
responsibility to make sure the structure to which this
component is attached can support five times the combined
weight of all equipment. Reinforce the structure as required
before installing the component.
WARNING
:
Exceeding the weight capacity
can result in serious personal injury or damage to equipment! It
is the installer’s responsibility to make sure the weight of all
components attached to the SL151 does not exceed 35 lbs
(15.9 kg).
WARNING
:
RISK OF INJURY! Do not place
video equipment such as televisions or computer monitors on
the ceiling panel of the SL151.
NOTE: This system has no user serviceable parts.