AmpliVox SW230A - Manual (Page 5)

5
1. Power Switch.
2. Power Indicator Light. Turns red when
power is turned on.
3. Mic Volume Control. This knob con-
trols output loudness to all 3 microphone
inputs and Siren.
4. Dynamic Mic Jack. Dynamic is one
kind of microphone. AmpliVox’s wired,
hand-held microphone is this type.
5. Auxiliary Volume Control. This vol-
ume knob controls the auxiliary volume
separately from the microphone volume.
6. Tone Control. This knob controls the
tone of the auxiliary input. Turn counter-
clockwise for more bass or clockwise for
more treble. (The mic jacks don’t need a
tone control because they have been pre-
optimized for the human voice.
7. Left & Right Speaker Jacks. Two sepa-
rately amplified speaker jacks allow you to
use one or two speakers for additional
sound power or true stereo output.
8. Line Out Jack. Can be used with a tape
recorder The Line Out Jack outputs all the
sound from the 3 microphone inputs and the
auxiliary input.
9. Auxiliary Line In Jack. To play music,
just plug in your CD player, MP3 player or
Amplivox’s Bluetooth Receiver.
10. Wireless Mic Jack. Optional second
wireless receiver goes here. Then plug Am-
pliVox’s lapel or headset microphone into
the transmitter. Now you are hands-free
anywhere within a 300- foot radius of the
receiver.
11. Condenser Mic Jack—with phantom
power. If you don’t know what phantom
power is, then you don’t need to know, but a
condenser microphone won’t work without it.
If you have AmpliVox’s lapel or headset
microphone, plug it in here.
12. Aux Out. For optional 12-15 volt
accessory.
13. DC In Jack. Used for the optional
International AC Adapter / Charger
(S1460), plug it in here. Plug the other
end into a wall / floor outlet.
14. Wireless ON/OFF Switch
Switches power on to the built-in 16
channel wireless receiver.
15. Wireless 16 Channel Selector
Channel that you select here must
match with the channel that is select-
ed on the bodypack microphone
transmitter.
16. Wireless 16 Channel UHF
Bodypack Microphone Transmitter.
Connect Lapel or Headset micro-
phone to MIC jack on top panel.
15. Wireless 16 Channel Selector (left
side of case
)—rotate knob to select wire-
less channel on the built-in receiver. RF LED
will light up when receiving signal from
transmitter.
16. Wireless 16 Channel
UHF Bodypack Microphone
Transmitter
Wireless Receiver Features Model SW230A
AMPLIFIER FEATURES
1. Power Switch
2. Power Indicator Light
3. Mic Volume-controls all
3 microphone inputs
4. Dynamic Mic
Jack— 1/4 ″ for
wired, hand-held
microphone
5. Auxiliary Volume—
controls the auxiliary
input separately from the
microphone volume
6. Tone Control—
for auxiliary input; counter-
clockwise for more bass; clock-
wise for more treble
7. Left & Right
Speaker Jacks— 1/4 ″
( 4—8 ohm input)
8. Line Out—3.5mm
record your presentation
with a tape recorder or a
computer sound card
9. Auxiliary Line In—
3.5mm add music with a
tape player, CD or MP3
player
10. Wireless Mic
Jack -3.5mm for
optional wireless
receiver
11. Condenser
Mic Jack - 3.5mm
for lapel or headset
microphone
12. Aux Out
- for optional
12-15 volt
accessory.
13. DC In Jack —
plug in optional Universal
AC Adapter/ Charger for
power.
14. Wireless ON/OFF Switch
Channel selected must match
15. Channel Selector