AmpliVox SW314 - Manual (Page 4)

4
1. Power Switch.
2. Power Indicator Light. Turns red when
power is turned on.
3. Siren Button. Single - Variable tone @125
dBL. Push and hold.
4. Mic Volume Control. This knob controls
output loudness to all 3 mic inputs and Siren.
5. Dynamic Mic Jack. Dynamic is one kind of
mic. AmpliVox’s wired, hand-held mic is this
type.
6. Auxiliary Volume Control. This volume
knob controls the auxiliary volume separately
from the mic volume.
7. Tone Control. This knob controls the tone of
the auxiliary input. Turn counter-clockwise for
more bass or clockwise for more treble. (The
mic jacks don’t need a tone control because
they have been pre-optimized for the human
voice.
To Operate:
8. Left & Right Speaker Jacks. Plug
speaker leads from speakers into the
two jacks.
9. Line Out Jack. Can be used with a
tape recorder The Line Out Jack out-
puts all the sound from the 3 mic inputs
and the auxiliary input.
10. Auxiliary Line In Jack. To play
music, just plug in your CD player, MP3
player or Amplivox Bluetooth Receiver.
11. Wireless Mic Jack. Optional se-
cond wireless receiver goes here. Then
plug AmpliVox’s lapel or headset mic
into the transmitter; that’s the one with
the belt clip. Now you are hands-free
anywhere within a 300- foot radius of
the receiver.
12. Condenser Mic Jack—with phan-
tom power. If you don’t know what
phantom power is, then you don’t need
to know, but a condenser mic won’t
work without it. If you have AmpliVox’s
lapel or headset mic, plug it in here.
13. Aux Out. For optional 12-15 volt
accessory.
14. DC In Jack. Used for the 12V
Battery Cable, 12V Power Plug or
the optional International AC Adapt-
er/Recharger, plug it in here. Plug
the other end into a wall / floor outlet.
15. Wireless ON/OFF Switch
Switches power on to the built-in 16
channel wireless receiver.
16. Wireless 16 Channel Selector
Channel that you select here must
match with the channel that is select-
ed on the bodypack microphone
transmitter.
17. Wireless 16 Channel UHF
Bodypack Microphone Transmit-
ter. Connect Lapel or Headset mi-
crophone here.
16. Wireless 16 Channel Selector (left
side of case, SW312, SW314
)—rotate
knob to select wireless channel on the built-
in receiver. RF LED will light up when re-
ceiving signal from transmitter.
17. Wireless 16 Channel
UHF Bodypack Microphone
Transmitter
Models SW312 / SW314 Wireless Features
AMPLIFIER FEATURES S312, SW312, S314, SW314
1. Power Switch
2. Power Indicator Light
3. Siren Button
4. Mic Volume-
controls all 3 mic
inputs 5. Dynamic Mic
Jack— 1/4 ″ for
wired, hand-held
mic.
6. Auxiliary Volume—
controls the auxiliary
input separately from the
mic volume
7. Tone Control—
for auxiliary input; counter-
clockwise for more bass; clock-
wise for more treble
8. Left & Right
Speaker Jacks— 1/4 ″
9. Line Out—3.5mm
record your presentation
with a tape recorder or a
computer sound card
10. Auxiliary Line In—
3.5mm add music with a
tape player, CD or MP3
player
11. Wireless Mic
Jack -3.5mm for
optional wireless
receiver
12. Condenser
Mic Jack - 3.5mm
for lapel or headset
mic
13. Aux Out
- for optional
12-15 volt
accessory.
14. DC In Jack —
plug in optional Universal
AC Adapter/ Recharger for
power.
15. Wireless ON/OFF Switch
Models SW312 / SW314
Channel selected must match
Insure the speakers are plugged into the “SPEAKER” jacks. Plug handheld microphone into the “DYNAMIC” jack. Turn amplifier on.
Turn microphone on and talk into microphone. Rotate “VOLUME” control knob to obtain desired loudness level. For Models SW312 /
SW314 the built-in wireless receiver ON-OFF switch is located just below main power switch of amplifier. Insure both transmitter and
receiver are on same frequency channel. Turn on power switch located on wireless transmitter. RF LED on side of amplifier will light
meaning that it is receiving signal. If RF LED does not light, check channels.
16. Wireless Channel Selector
Models SW312 / SW314 -
on side