AmpliVox SW805A - Manual (Page 4)

4
1. Power Switch.
2. Power Indicator Light. Turns red when
power is turned on.
3. Mic Volume Control. This knob con-
trols output loudness to all 3 microphone
inputs and Siren.
4. Dynamic Mic Jack. Dynamic is one
kind of microphone. AmpliVox’s wired,
hand-held microphone is this type.
5. Auxiliary Volume Control. This vol-
ume knob controls the auxiliary volume
separately from the microphone volume.
6. Tone Control. This knob controls the
tone of the auxiliary input. Turn counter-
clockwise for more bass or clockwise for
more treble. (The mic jacks don’t need a
tone control because they have been pre-
optimized for the human voice.
7. Left & Right Speaker Jacks. Two sepa-
rately amplified speaker jacks allow you to
use one or two speakers for additional
sound power or true stereo output.
8. Line Out Jack. Can be used with a tape
recorder The Line Out Jack outputs all the
sound from the 3 microphone inputs and the
auxiliary input.
9. Auxiliary Line In Jack. To play music,
just plug in your CD player, MP3 player or
Amplivox’s Bluetooth Receiver.
10. Wireless Mic Jack. Optional second
wireless receiver (S1690R) plugs in here.
Then plug AmpliVox’s lapel or headset mi-
crophone into the transmitter. Now you are
hands-free anywhere within a 300- foot radi-
us of the receiver.
11. Condenser Mic Jack—with phantom
power. If you don’t know what phantom
power is, then you don’t need to know, but a
condenser microphone won’t work without it.
If you have AmpliVox’s lapel or headset
microphone, plug it in here.
12. Aux Out. For optional 12-15 volt
accessory.
13. DC In Jack. Used for the 12V
Battery Cable, 12V Power Plug or the
optional International AC Adapter/
Recharger, plug it in here. Plug the
other end into a wall / floor outlet.
14. Wireless ON/OFF Switch
Switches power on to the built-in 16
channel wireless receiver.
15. Wireless 16 Channel Selector
Channel that you select here must
match with the channel that is select-
ed on the bodypack microphone
transmitter.
16. OPTIONAL—Wireless 16 Chan-
nel UHF Bodypack Microphone
Transmitter (S1690T) Connect Lapel
or Headset microphone here.
16. Wireless 16 Channel Selector (left
side of case
)—rotate knob to select wire-
less channel on the built-in receiver. RF LED
will light up when receiving signal from
transmitter.
17. Optional—Wireless 16
Channel UHF Bodypack
Microphone Transmitter
Model SW805A Wireless Features
AMPLIFIER FEATURES
1. Power Switch
2. Power Indicator Light
3. Mic Volume-
controls all 3 mic
inputs 4. Dynamic Mic
Jack— 1/4 ″ for
wired, hand-held
mic.
5. Auxiliary Volume—
controls the auxiliary
input separately from the
mic volume
6. Tone Control—
for auxiliary input; counter-
clockwise for more bass; clock-
wise for more treble
7. Left & Right
Speaker Jacks— 1/4 ″
8. Line Out—3.5mm
record your presentation
with a tape recorder or a
computer sound card
9. Auxiliary Line In—
3.5mm add music with a
tape player, CD or MP3
player
10. Wireless Mic
Jack -3.5mm for
optional wireless
receiver
11. Condenser
Mic Jack - 3.5mm
for lapel or headset
mic
12. Aux Out
- for optional
12-15 volt
accessory.
13. DC In Jack —
plug in optional Universal
AC Adapter/ Recharger for
power.
14. Wireless ON/OFF Switch
Model SW805A
Channel selected must match
Plug handheld microphone into the “DYNAMIC” jack. Check to see that you have plugged in your speakers. Turn amplifier on. Turn
microphone on and talk into microphone. Rotate “VOLUME” control knob to obtain desired loudness level. For Model SW805A with
the built-in wireless receiver the “ON-OFF” switch is located just below main power switch of amplifier. Make sure both transmitter and
receiver are on same frequency channel. Turn “ON” wireless transmitter (S1690T). RF LED on side of amplifier will light, meaning
that it is receiving signal. If RF LED does not light, check channel numbers.
To Operate:
15. Wireless Channel Selector
Model SW805A