Analog Way Smart Edge FX - Manual

QUICK START GUIDE
What’s in the box
Quick install and setup
Thank you for choosing Analog Way and the Smart Edge FX . By following these simple steps, you will be able to
setup and use your powerful Hi-Resolution Mixer Switcher with Dual Output Edge Blending within minutes. Discover
the
Smart Edge FX H[WHQVLYHFDSDELOLWLHVDQGLQWXLWLYHLQWHUIDFHZKLOHFRQ¿JXULQJ\RXU¿UVWVKRZDQGXQOHDVK\RXU
creativity for a new experience in show and event management by Analog Way .
Smart Edge FX - Ref. STE200
1 x Smart Edge FX (STE200)
1 x AC Power cable
2 x DVI-I male to HD15 female and DVI-D female breakout cable
1 x HD15 to 5 BNC cable
1 x Ethernet cross cable (for device update)
1 x Set of 11 audio 5-pin screw terminals
1 x RCS - Remote Control Software (PC only) *
1 x User Manual (PDF version) *
1 x Quick Start guide *
* Download on our website: www.analogway.com
Optional:
1 x Sync Cable for multiple machine mode (Ref. AW212080)
WARNING !
If required, front handles of the device can be dismantled,
but with caution.
The original screws removed must not be reintroduced to
their location without handles in place.
Substantial damages can occur, including risk of elec-
tric shock from the mains voltage.
Only M4x12mm screws can be used.
(They are supplied with the unit)
Getting started g :
You may wish to reset the unit to factory settings to get started.
Go to:
Menu --> Control --> Default Values --> Yes .
1. Select the Output resolution that matches the native
resolution of your display. You will next be prompted to
choose enable follow mode if desired and output rate.
Menu --> Output --> Output format --> 1024x768 -->
Internal Ref --> 60 Hz
.
2. The principle of Soft Edge Blending lies in projecting an
image on a wide screen thanks to two or more video
projectors displaying the same content.
We Invite you to read the User Manual if your skills are not
enough to achieve the necessary adjustments.
The following setup has to be made throught an external
Remote Control (RCS/RK-300/TRK-800/ORC50/ARC200).
3. On your controller, to display a source, select the
[BACKGROUND LIVE] layer (it will begin to blink)
then, select a source (it will also blink). Press [TAKE] to
transition on program output.
There will always be a layer selected (blinking) and a source
selected (blinking) to the selected layer (blinking). To change
the contents of a different layer, simply select it. The Smart
Edge FX has 2 layers available called:
[BACKGROUND LIVE]
and [PIP] .
Each layer will obscure your view other layer below.
4. To display a titling, select the [PIP] layer, (it will begin to
blink) then select your source (it will also blink). Press
[TAKE] to display the PIP on program out.
The title layer is only available by an external Remote Control
(RCS/RK-300/TRK-800/ORC50/ARC200).
The Layer selection section allows to adjust Layer size,
position, transparency or transitions.
The Keying/Tilting section allows to access keying and titling
controls and parameters.
The Keyed layer has similar capabilities than any other layers.
RK-300, TRK-800 and RCS allow to control the Keyed Layer
by the
[PIP2] button.
ORC50 or ARC200 allow to control the Keyed Layer by [PIP1]
button.
To see the layer beneath, you will need to clear or move the
layer that are the top.
5. To clear the PIP, select the layer (it will blink) then, select
[BLACK] . Press [TAKE] to remove the layer from the
program output.
IMPORTANT: T T
Simply selecting a menu item will not set it to that value.
Be sure to press the ENTER button when parametering the
menu items.