Analog Way Smart Edge - Manual

QUICK START GUIDE
What’s in the box
Quick install and setup
Thank you for choosing Analog Way and the Smart Edge . By following these simple steps, you will be able to setup and
use your powerful Hi-Resolution Mixer Switcher with Dual Output Edge Blending within minutes. Discover the Smart
Edge extensive capabilities and intuitive interface while configuring your first show, and unleash your creativity for a new
experience in show and event management by Analog Way .
Smart Edge - Ref. STE100
1 x Smart Edge (STE100)
1 x AC Power cable
2 x DVI-I male to HD15 female and DVI-D female breakout cable
1 x HD15 to 5 BNC cable
1 x Ethernet cross cable (for device update)
1 x Set of 3 audio 5-pin screw terminals
1 x RCS - Remote Control Software (PC only) *
1 x User Manual (PDF version) *
1 x Quick Start guide (PDF version) *
* Download on our website: www.analogway.com
Optional:
1 x Sync Cable for multiple machine mode (Ref. AW212080)
WARNING !
If required, front handles of the device can be dismantled,
but with caution.
The original screws removed must not be reintroduced to
their location without handles in place.
Substantial damages can occur, including risk of elec-
tric shock from the mains voltage.
Only M4x12mm screws can be used.
(They are supplied with the unit)
Getting started:
You may wish to reset the unit to factory settings to get started.
Go to: Menu --> Control --> Default Values --> Yes .
1. Select the Output resolution that matches the native
resolution of your display. You will next be prompted to
choose enable follow mode if desired and output rate.
Menu --> Output --> Output format --> 1024x768 -->
Internal Ref --> 60 Hz .
2. The principle of Soft Edge Blending lies in projecting an
image on a wide screen thanks to two or more video
projectors displaying the same content.
We Invite you to read the User Manual if your skills are not
enough to achieve the necessary adjustments.
To see in the User Manual: Page 32 to 34 and page 50 to 54.
3. To display a source, select the [BACKGROUND LIVE]
layer (it will begin to blink) then, select a source (it will
also blink). Press [TAKE] to transition your source from
preview to program output.
There will always be a layer selected (blinking) and a source
selected (blinking) to the selected layer (blinking). To view on
preview or change the contents of a different layer, simply
select it. The Smart Edge has 2 layers available called:
[BACKGROUND LIVE] and [DSK] .
Each layer will obscure your view other layer below.
4. To display a titling, select the [PIP] layer, (it will begin to
blink) then select your source (it will also blink). Press
[TAKE] to display the PIP on program out.
The title layer is only available by an external Remote Control
(RCS/RK-300/TRK-800/ORC50/ARC200).
The Layer selection section allows to adjust Layer size,
position, transparency or transitions.
The Keying/Tilting section allows to access keying and titling
controls and parameters.
The Key layer has similar capabilities than any other layers.
The only constraint is that this layer must necessarily contain a
source of keying that is already applied.
Otherwise the source will be converted to black.
RK-300, TRK-800 and RCS allow to control the Key Layer by
the [PIP2] button.
ORC50 or ARC200 allow to control the Key Layer by [PIP1]
button.
To see the layer beneath, you will need to clear or move the
layer that are the top.
5. To clear the PIP, select the layer (it will blink) then, select
[BLACK] . Press [TAKE] to remove the layer from the
program output.
IMPORTANT:
Simply selecting a menu item will not set it to that value.
Be sure to press the ENTER button when parametering the
menu items.